Home » Home DIY Repair » Plumbing » How To Install A Water Line To Your Refrigerator – Easy Step-By-Step Installation

How To Install A Water Line To Your Refrigerator – Easy Step-By-Step Installation

Here is a step-by-step water line installation refrigerator guide. A new refrigerator with a water dispenser and ice maker needs to be hooked up to a COLD water line. Usually behind where a refrigerator is installed, there will be a water valve that you can use to hook cold water to your fridge. If there is no water valve behind your fridge, you will have to run a water line to the closest cold water pipe to get your refrigerator access to water. You may have a cold water pipe either behind the wall where the fridge is or possibly in the floor under the kitchen. You will need to locate where the cold water pipe is, drill to access it, and install a water valve and flexible water tubing. This usually will take an hour and a half or so to complete. You will need a refrigerator water line installation kit, a drill, a wrench, drill bits, a screwdriver, and a water line cutter to complete this project.

Below is step-by-step instructions for installing a water line to your fridge.

how to install a refrigerator water lineHow to install a refrigerator water line?

NOTE: If you already have an installed cold water valve behind your refrigerator, all you will need to hook up your fridge to water is some flexible plastic water tubing going from the wall valve to the fridge water inlet valve.

Refrigerator Ice Maker Water Line Installation KitRefrigerator Ice Maker Water Line Installation Kit
You will need a fridge water line kit if you have no water valve already installed

Here is how to tap into the cold water pipe and get cold water to your refrigerator ice maker and water dispenser:

Step 1 – Locate and select the COLD water pipe in the floor or wall you will be using for the fridge water line. (If you have a choice, select a vertical pipe not horizontal, as sediment can enter the fridge water line easier)

water line valve or saddle valve for refrigerator2 Types of Water Valves can be used
Saddle Valve or In Wall Water Valve for Refrigerator Water Line

Step 2 – You will be drilling a hole into the cold water pipe so turn off the main water supply to your complete house.

Step 3 – Gain access to the cold water pipe (in the wall or floor) and drill a 1/4″ hole into the pipe making sure it is as centered as possible. Make sure NOT to drill too far and make another hole out the other side of the pipe.

Step 4 – Use the water valve (saddle valve) that came with your fridge water line kit and attach it to the cold water pipe using a screwdriver and the clamps it came with.

saddle valve for refrigerator water lineSaddle valve for refrigerator water line

Step 5 – Attach it right over the hole you drilled. Get the screws on the clamps tight enough until the sealing washer or gasket swells up. This sealing washer is what prevents water leaks so be sure it is tight enough until it swells to cover and seal the hole. Do not tighten the clamps with excessive force as you can actually distort the copper piping.

Step 6 – Get out the plastic water tubing from your fridge water line kit. Start the line from the refrigerator but do not install it onto the fridge yet. You may have to drill a hole through the wall or the floor if needed to get the other end to the water valve. Keep an extra 8 to 10 feet of water tubing rolled up neatly behind the refrigerator to allow enough tubing to be pulled out if you have to slide the refrigerator away from the wall.

water supply line for fridgeWater supply line tubing for fridge
Leave extra 8 to 10 feet to allow to pull fridge out when needed

Step 7 – Put the compression nut and ferrule onto the water tubing that came with your kit. Connect the water tube to the water valve and tighten the nut with your hand, then turn once more with a wrench. Do not over tighten.

Step 8 – Now your plastic water tube should be connected to the cold water valve you just installed. You need to clear out the water tubing to get out any gunk before attaching it to your fridge. Get a large empty bucket. Put the end of the water line into the empty bucket. Turn the main water on to your home. Now, turn the new water valve on with the end of the water line in the bucket. This will flush the gunk from the tube into the bucket. Run the water line into the bucket until the water is perfectly clean and clear. Once the water is clear, turn off the new water valve.

Step 9 – Now the other end of your water tubing needs to be connected to the refrigerator. Slide on the pressure nut and then the ferrule from the water line kit onto the plastic water line then carefully attach the nut (water line) to the refrigerator water inlet valve. Do not over tighten.

Step 10 – Now it is time to check for water leaks. Turn the water on at the water valve you just installed. If you find any leaks simply tighten the nuts or the screws on the water valve only slightly until leak stops. Never over tighten.

Step 11 – If there are no leaks, plug in your refrigerator and turn the ice maker on. When the ice maker makes ice for the first 4 times, throw the ice away as it will contain debris from inside the tubing in the fridge/freezer. If you have a water dispenser on your fridge, dispense about a gallon of water and spill it down the kitchen sink drain. This is to flush the water tubing system which can have debris or dirt from the manufacturing process.

Your fridge should now have a perfectly working ice maker and water dispenser!

If your fridge has a water filter that filters all the water and ice, we can help you to replace the water filter. Depending on brand of refrigerator, you will need certain types of water filters. Here are the water filters for GE, Samsung, LG, Maytag, and Whirlpool. If you need help replacing the filter, here is a guide to replace a refrigerator water filter.


How to install a water line to your fridge so you can use your fridge’s ice maker and water dispenser

If you know of an easier way to install a water line for a refrigerator ice maker and water dispenser, please leave a comment below.

Leave a Reply

3 thoughts on “How To Install A Water Line To Your Refrigerator – Easy Step-By-Step Installation”

  1. ALLEN VETTER - DIY Repair Assistant

    jose,
    We assume you are installing a refrigerator in your garage.
    Do you have all the necessary parts to install the water line in your garage?
    What is your exact question?
    -RR

  2. Hi I have purchased a Samsung side by side American style fridge freezer, I’ve looked at the water connector on the back, the lower pipe on the bottom right of the valve feeds the Ice maker but the pipe on the bottom left isn’t connected to anything, could anyone tell me what this pipe is for and if it should be connected to any place? Many thanks

Leave a Comment

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.