Home » Home DIY Repair » Clothes Dryer Repair » LG Dryer Error Fault Codes – What To Check – How To Fix

LG Dryer Error Fault Codes – What To Check – How To Fix

LG dryer displays an error code? The error codes below will help you troubleshoot the problem with your LG dryer. These error codes can tell you what to check, repair, or replace. These error codes can help you to find the issue and fix your LG dryer yourself.

LG dryer error codesLG dryer error codes

LG Dryer Error Code = d80 d90 or d95
Error Condition = Flowsense indicator = Exhaust system
Check and or Repair = Check that the dryer’s exhaust system is not blocked from the dryer to the outside of the home. This is the result of lint buildup in the exhaust duct. (The error codes d80, d90, and d95 tell you that the dryer’s exhaust duct is clogged 80%, 90%, or 95%. The dryer will turn off after 2 minutes and a warning sound will be heard from the dryer)
Clean out air vent exhaust lines.

LG Dryer Error Code = FO (Filter Out)
Error Condition = Filter not installed properly
Check and or Repair = Check that the lint filter is inserted properly.
(If the lint filter is not installed correctly the dryer will stop working. Remove the lint filter and reinsert it into the lint filter housing)

LG Dryer Error Code = PS
Error Condition = Improper voltage with the power cord
Check and or Repair = Be sure the white and red wire connections bare not reversed on the dryer’s terminal block.
Remove power and rewire.

LG Dryer Error Code = CL (Child Lock Display)
Error Condition = An indication that the Child Lock feature is active.
Check and or Repair = Press and hold the key labeled CHILD LOCK for 3 seconds to disable the Child Lock feature.

LG Dryer Error Code = tE1
Error Condition = Thermistor failure
Check and or Repair = The control detects the temperature sensor is defective. Remove power from the dryer and measure resistance through the thermistor. It should measure about 10,000 ohms. If the thermistor is defective then replace it.
MORE INFO:
-Unplug the dryer, or trip the circuit breaker supplying power to the dryer.
-While the dryer remains without power, press and hold the START/PAUSE button for 5 seconds.
-Restore power to the dryer and try to run another cycle.
Replacement Parts = Thermistor

LG Dryer Error Code = tE2
Error Condition = Thermistor failure
Check and or Repair = The control detects the temperature sensor is defective. Remove power from the dryer and measure resistance through the thermistor. It should measure about 10,000 ohms. If the thermistor is defective then replace it.
MORE INFO:
-Unplug the dryer, or trip the circuit breaker supplying power to the dryer.
-While the dryer remains without power, press and hold the START/PAUSE button for 5 seconds.
-Restore power to the dryer and try to run another cycle.
Replacement Parts = Thermistor

LG Dryer Error Code = tE3
Error Condition = Thermistor failure
Check and or Repair = The control detects the temperature sensor is defective. Remove power from the dryer and measure resistance through the thermistor. It should measure about 10,000 ohms. If the thermistor is defective then replace it.
MORE INFO:
-Unplug the dryer, or trip the circuit breaker supplying power to the dryer.
-While the dryer remains without power, press and hold the START/PAUSE button for 5 seconds.
-Restore power to the dryer and try to run another cycle.
Replacement Parts = Thermistor

LG Dryer Error Code = E13
Error Condition = The drain hose is kinked, crushed, clogged, or the water in the sump is frozen.
Check and or Repair = Check that the drain hose is not kinked, twisted, or clogged with water at the end of the hose.
-Press the START/PAUSE button to start the dryer again after checking that the drain hose is not kinked, twisted, or clogged.

LG Dryer Error Code = nP
Error Condition = There is a problem with the electrical wiring in the home and no current is being detected at the heater.
Check and or Repair = Check power

LG Dryer Error Code = dE
Error Condition = Door switch error
Check and or Repair = Check the operation of the door switch. Do this by using the diagnostic test mode. If the door switch is defective then it needs to be replaced.
Replacement Parts = Door switch

LG Dryer Error Code = HS
Error Condition = Dryer has detected an error with the humidity sensor. (The HS error code will cause the dryer to run for 2 1/2 hours, which may seem as though the dryer is not drying.)
Check and or Repair = Clean the sensors on the inside of the dryer that are located below the lint filter. Allow the sensors to fully dry before attempting another cycle.

LG Dryer Error Code = Add Water
Error Condition = There is a water supply error
Check and or Repair = Before using a steam cycle the steam feeder must be filled with water up to the MAX indicator lines. Check the steam feeder to be sure that it is full of water and that the drawer is completely closed.
If the Add Water reading appears on the dryer’s display after a cycle has started:
-Press PAUSE to temporarily stop the running cycle.
-Fill the steam feeder with tap water to the MAX fill line.
-Power the unit off and back on again, select the STEAM cycle, and press the START/PAUSE button to finish the cycle.

LG DRYER replacement partsOnce you find out what part your dryer needs, here are LG DRYER replacement parts

More clothes dryer troubleshooting for Frigidaire Dryer Error Codes, GE Dryer Error Codes, Kenmore Dryer Error Codes, LG Dryer Error Codes, Maytag Dryer Error Codes, Samsung Dryer Error Codes, and Whirlpool Dryer Error Codes.

If your LG dryer error code is not listed here, please leave a comment below and we will be happy to assist you with your issue.

Leave a Reply

35 thoughts on “LG Dryer Error Fault Codes – What To Check – How To Fix”

  1. Appliance Repair Assistant

    JOHN,
    LG Dryer Error Code nE = Vibration Sensor Error = This error code shows when the Vibration Sensor Communication is not working such as vibration sensor register setup error or removal.
    -RR

  2. My LG DLE5955G just had the heating assembly replaced and now the Est Time Remaining just flashes and dryer will not start. Any advice is greatly appreciated.

  3. It is actually trying to spell gAS. This message means that the dryer is not getting the proper gas supply. You should make sure the gas valve is fully open. If this is a new install and opening the valve does not resolve the issue, you should contact the installer. If the dryer is not new and the gas valve is fully open, the unit needs service.

  4. Hi Leah,
    Did you ever get this sorted? If so what was the fix?

    Our 3 month old dryer is doing the same thing and we had a gas plumber check all the lines and everything is fine but the dryer is still giving issues.

    Thank you.

  5. LG dlex3250 dryer no error codes just a flash of lines going around display where the amount of time is.

  6. I have an LG dryer that will run for a few seconds then stop for a minute or so then repeat that process. I did the diagnostics on it and the flow sensor went to four bars. So I took apart the filter system and cleaned it completely. I also cleaned out the vent system. I seem to have good airflow from the dryer when the vent is unhooked. I also have essentially the same airflow from the outside. I have tried resetting the dryer with no results. Any ideas on what can be causing this?

  7. Mine just started happening as well. It’s actually “gAS”. I called Lg and they said to make sure the gas valve is on and that it’s not kinked.
    I ended up having to have someone come out and check it out

  8. I just purchased my lg dryer from Best Buy outlet I am also getting a 9A5 code that I cannot find in the manual!! Please help!! Dryer won’t dry and stops in the middle of cycle .

  9. I have the same problem. 9A5 is flashing. This thing is brand new. I am so pisssd right now. The code is not listed anywhere. Does any company do the right the thing anymore. Can’t find answers. It’s brand new!

  10. Dryer stopped working and started flashing a “9A5” code. Not listed in manual, and I can’t find it anywhere online.

  11. My codes are 18 E8. The dryer will start and run fine if you hit start multiple times. Is it the motor? The power wire to the control board wont click in but does get power . It will pull out easily, wont lock in.

  12. Have a new dryer about 3 months old. Unit stopped drying and giving an error code 9A5 which I cannot find anywhere… My model IS DKGX7801

  13. When I turn on my LG Steam dryer it beeps real fast and the check filter light is flashing. I cleaned the sensor and it is still doing the same thing.

  14. I had an error code to replace the door switch, which I did. Now when I select the power button, it turns the dryer on and then I select a dryer setting, the lights come on and when I push the start button the dryer does not start running and instead there is only a clicking sound and the drying light flashes on and off. There are no other error codes.

  15. I turn the dryer on & it starts than it stops & the code EE2 comes up? I turn off & start again & all is fine? What does this code mean?

  16. My LG Tru Steam dryer will not turn off. There is no error code (the screen is blank) and the dryer will only turn off when the door is opened. The dryer is not heating when it is running, the vent is clear. To stop the dryer the dryer must be unplugged. The tech is here and is stumped. What is a possible cause/remedy? The dryer is 1.5 to 2 years old.

  17. power button turns dryer machine on and the select a dryer setting lights come on and I can select a dryer setting but when push the start button the dryer does not start running and instead there is a clicking sound when I push the start button and the processing drying light flashes on and off

  18. Christian Baysa

    LG Washing Machine Model WF-T1181TH
    When turn on the power it will display “bE”
    Keeps beeping and doesnt work at all, just displays error and beeps
    Thanks

  19. DIY Project Help Tips

    Holly Klope,
    Attempt to reset the LG Dryer by removing power for 10 minutes.
    Reapply power and see if this may fix it.
    If not you may have a faulty control board or a wiring problem.
    -RR

  20. LG Dryer won’t start at all.
    Heat won’t go up and down on any setting.
    Nothing adjustable.
    Dryer LG sensor Dry 011531020182A091658 121R1163.
    We have tried everything.

  21. Rob carpentier

    I have an LG dryer number DLG5988W.
    My dryer spins but has no heat.
    I replace the igniter still no heat.
    The dryer is giving me a 19:FO.
    Please help with error code or part needed.

Leave a Comment

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.