Home » Home DIY Repair » Oven Repair » Whirlpool Oven Error Codes – What To Check – How To Clear

Whirlpool Oven Error Codes – What To Check – How To Clear

Whirlpool Stove, Range, and Oven error codes list. Error codes appear on your Whirlpool oven’s display to let you know there is a problem. This complete list of Whirlpool oven fault code definitions will assist you in finding the issue. Use the codes below to clear, check, troubleshoot, and repair your oven. Once you understand the error code displayed, you will know which part of the oven is faulty and causing the error. You can then purchase the part and fix the oven yourself. There are 3 letter error codes, 2 digit error codes, and 4 digit error codes on Whirlpool ovens. This means your Whirlpool oven will show either only 2 digits or two sets of 2 digits with a letter and a number. Example of 4 digit error code = e2 f3.

Whirlpool Oven Error Codes - What To Check - How To Clear

Whirlpool Range, Stove, Oven 3 Letter Error Codes:

Whirlpool Oven Error Code LOC
Reason/Condition for Error Code = Child LOCK is ON
Check/Troubleshoot = Press and hold the ‘Start’ or ‘Cancel’ button for ten seconds to remove LOC from display.

Whirlpool Oven Error Code PSH
Reason/Condition for Error Code = If Start is not pressed within 5 seconds, “PUSH” or “PSH” appears on the display – Press Start
If start is not pressed within 1 minute after pressing the keypad then the function is canceled and time is displayed.
Check/Troubleshoot = Reset power to the oven if you get a constant PSH error:
-Turn OFF circuit breaker to oven for one minute.
-Turn ON circuit breaker to oven.
-Check the oven for one minute to be sure the error code is cleared.

Whirlpool Range, Stove, Oven 2 Digit Error Codes:

Whirlpool Oven Error Code F0
No previous fault codes – press CANCEL to clear

Whirlpool Oven Error Code F1
Reason/Condition for Error Code = Defective Electronic Oven Control or EOC
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker – If F1 error persists then replace EOC
Replace/Check Parts = Electronic Oven Control (EOC)

Whirlpool Oven Error Code F2
Reason/Condition for Error Code = Oven Temperature Too High
Check/Troubleshoot = Check for welded contacts on both the bake and broil relays
Replace/Check Parts = Contact Relay – Control Board

Whirlpool Oven Error Code F3
Reason/Condition for Error Code = Open Oven Temperature Sensor
Replace/Check Parts = Replace Oven Temperature Sensor

Whirlpool Oven Error Code F4
Reason/Condition for Error Code = Oven Temperature Sensor Shorted
Replace/Check Parts = Replace Oven Temperature Sensor

Whirlpool Oven Error Code F5
Reason/Condition for Error Code = Control Board Fail
Replace/Check Parts = Replace Control Board

Whirlpool Oven Error Code F7
Reason/Condition for Error Code = Function Key Is Stuck
Replace/Check Parts = Replace Control Board

Whirlpool Oven Error Code F8
Reason/Condition for Error Code = Control Board Fail
Replace/Check Parts = Replace Control Board

Whirlpool Oven Error Code F9
Reason/Condition for Error Code = Oven Door Locking Fail
Check/Troubleshoot = Check door lock switches, stuck lock switch, wiring
Replace/Check Parts = Door Lock Switch

Whirlpool Oven Range Stove PartsWhirlpool Oven Range Stove Parts

Whirlpool Range, Stove, Oven 4 Digit Error Codes:

Whirlpool Oven Error Code F2 E0 (E0 F2)
Reason/Condition for Error Code = Keypad Wiring Harness NOT Connected
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Reconnect keypad wiring harness. Plug the oven power cord back in or turn ON circuit breaker. Press CANCEL on the display. If fault code comes back after 1 minute then replace the keypad. If F2 E0 persists then replace the electronic oven control.
Replace/Check Parts = Keypad – Electronic Oven Control

Whirlpool Oven Error Code F2 E5 (E5 F2)
Reason/Condition for Error Code = CANCEL Key (Button) Is Faulty
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Reconnect keypad wiring harness. Plug the oven power cord back in or turn ON circuit breaker. Press CANCEL on the display. If fault code comes back after 1 minute then replace the keypad. If F2 E5 persists then replace the electronic oven control.
Replace/Check Parts = Keypad – Electronic Oven Control

Whirlpool Oven Error Code F2 E6 (E6 F2)
Reason/Condition for Error Code = CANCEL Key (Button) Is Faulty
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Reconnect keypad wiring harness. Plug the oven power cord back in or turn ON circuit breaker. Press CANCEL on the display. If fault code comes back after 1 minute then replace the keypad. If F2 E6 persists then replace the electronic oven control.
Replace/Check Parts = Keypad – Electronic Oven Control

Whirlpool Oven Error Code F3 E0 (E0 F3)
Reason/Condition for Error Code = Open Oven Temp Sensor Circuit OR Oven Temp Sensor Faulty
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Reconnect the oven temperature sensor wiring harness. Replace the wire harness if shorted. Use an ohm meter and check the oven temp sensor resistance. If resistance is not 1080 ohms at room temp then replace the oven temperature sensor. If oven temp sensor resistance checks good then replace the electronic oven control.
Replace/Check Parts = Oven Temperature Sensor – Wiring Harness – Electronic Oven Control

Whirlpool Oven Error Code F3 E1 (E1 F3)
Reason/Condition for Error Code = Oven Temp Sensor Faulty OR Shorted Oven Temp Circuit
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Reconnect the oven temperature sensor wiring harness. Replace the wire harness if shorted. Use an ohm meter and check the oven temp sensor resistance. If resistance is not 1080 ohms at room temp then replace the oven temperature sensor. If oven temp sensor resistance checks good then replace the electronic oven control.
Replace/Check Parts = Oven Temperature Sensor – Wiring Harness – Electronic Oven Control

Whirlpool Oven Error Code F3 E2 (E2 F3)
Reason/Condition for Error Code = Oven Temp Over 575 Degrees In BAKE Mode
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Reconnect the oven temperature sensor wiring harness. Replace the wire harness if shorted. Use an ohm meter and check the oven temp sensor resistance. If resistance is not 1080 ohms at room temp then replace the oven temperature sensor. If oven temp sensor resistance checks good then replace the electronic oven control.
Replace/Check Parts = Oven Temperature Sensor – Wiring Harness – Electronic Oven Control

Whirlpool Oven Error Code F3 E3 (E3 F3)
Reason/Condition for Error Code = Oven Temp TOO HIGH In CLEAN Mode
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Reconnect the oven temperature sensor wire. Replace the wire harness if shorted. Measure the oven temp sensor resistance using a volt/ohm meter. If resistance is not 1080 ohms at room temp then replace the oven temperature sensor. If the oven temperature sensor resistance and wire harness connections a check good then replace the electronic oven control.
Replace/Check Parts = Oven Temperature Sensor – Wire Harness – Electronic Oven Control

Whirlpool Oven Error Code F4 E1 (E1 F4)
Reason/Condition for Error Code = Meat Probe Faulty/Shorted
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Use a volt/ohm meter and measure the resistance of the meat probe. If resistance is not 59000 ohms at room temp then replace the meat probe. If resistance of meat probe checks good then insert the meat probe and check for a secure connection with probe and jack. If jack is worn then replace. Check that the wire harness on the meat probe jack is not loose. Replace the wire harness if needed.
Replace/Check Parts = Meat Probe – Meat Probe Jack – Wire Harness

Whirlpool Oven Error Code F5 E0 (E0 F5)
Reason/Condition for Error Code = Door Open BUT Latch Is LockedLatch Switch Communicates A Locked Door
Check/Troubleshoot = Test the oven door switch by opening and closing the door. See if the oven light turns on and off. If the oven door switch is faulty then replace it. Unplug the oven power cord or turn OFF the circuit breaker. Connect any loose wire harnesses on the oven door lock assembly. Replace the wire harness if needed. Check the door lock assembly for faults and replace it if faulty.
Replace/Check Parts = Oven Door Switch – Oven Door Locking Assembly – Wire Harness

Whirlpool Oven Error Code F5 E1 (E1 F5)
Reason/Condition for Error Code = Self Clean Latch Will Not Lock or Unlock
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Reconnect loose wires on the oven door lock assembly wire harness. Replace wire harness if needed. Check the door lock assembly for faults and replace it if faulty.
Replace/Check Parts = Oven Door Locking Assembly – Wire Harness

Whirlpool Oven Error F5 E1Whirlpool Oven Error F5 E1

Whirlpool Oven Error E1 F2Whirlpool Oven Error E1 F2


Parts below are for Whirlpool Oven – Range – Stove
In association with replacement parts due to error codes.

Whirlpool Electronic Control for Range OvenWhirlpool Electronic Control for Range Oven

 

Whirlpool Oven Electronic ControlWhirlpool Oven Electronic Control

 

 

Whirlpool Oven Control Panel AssemblyWhirlpool Oven Control Panel Assembly

 

 

Whirlpool Oven Sensor for RangeWhirlpool Oven Sensor for Range

 

 

Whirlpool Terminal Block for Range OvenWhirlpool Terminal Block for Range Oven

 

 

Whirlpool Infinite Switch for Range OvenWhirlpool Infinite Switch for Range Oven

 

 

Whirlpool Sensor for Range OvenWhirlpool Sensor for Range Oven

 

 

Whirlpool Oven Bake ElementWhirlpool Oven Bake Element

Need help repairing or troubleshooting an error code on your Whirlpool Oven, Range, or Stove? Leave your question below and we will be happy to assist you in fixing the problem.

Leave a Reply

56 thoughts on “Whirlpool Oven Error Codes – What To Check – How To Clear”

  1. Appliance Repair Assistant

    Christopher,
    Not sure if you typed it wrong but C3-E1 is not a known error code for Whirlpool ovens.
    The error code that we have in our database is F3-E1.

    An F3 E1 error code on your Whirlpool oven/range combo typically indicates an issue with the oven temperature sensor or its wiring. To troubleshoot and resolve this issue…

    Disconnect power: Before attempting any repairs or troubleshooting, unplug the oven or switch off the circuit breaker to ensure your safety.
    Check the oven temperature sensor: The oven temperature sensor is usually located near the back wall of the oven cavity. Inspect it for any visible signs of damage or wear.
    Check the wiring: Inspect the wiring between the oven temperature sensor and the control board. Look for any loose connections, damaged wires, or signs of corrosion.
    Test the sensor: You can test the oven temperature sensor using a multimeter. Disconnect the sensor from the wiring and measure its resistance. At room temperature (around 20°C or 68°F), the resistance should be approximately 1080-1100 ohms. If the resistance is significantly different, the sensor may be faulty.
    Replace the sensor if necessary: If the sensor is found to be faulty, replace it with a new one. Make sure to use a compatible replacement part for your specific Whirlpool oven/range combo model.
    Reconnect power and test: Once the issue has been resolved, reconnect the power supply, and test the oven to ensure it is functioning correctly.

    Hope this can help…

    -RR

  2. F3 E1 error code on my Whirlpool oven/range combo.
    It won’t heat but the numbers climb to the set degree.
    Been told it’s the thermostat in the oven and the lower element… I can’t find the error code on any platform.

  3. HOW DO YOU RESET OR CORRECT Whirlpool Oven Error Code F5 E0
    (LATCH IS LOCKED BUT OVEN DOOR IS OPEN)

  4. I have a single wall oven that when on clean cycle would run about an hour and shut off with PF showing. Now my oven will not come on at all but the clock & display works. Any ideas?

  5. ALLEN VETTER - DIY Repair Assistant

    Jonathan,
    What happens with your Whirlpool stove when the display says: “Fault detected press start”… Do you press START, and if so, what happens next?
    What is the model number of your Whirlpool Oven/Stove?
    -RR

  6. My whirlpool model_WFE770H0FZ0 range beeps every 20 seconds, even when not in use. What causes this and must be done to correct this problem?

  7. I have an error code of F6 E1 on my whirlpool electric oven that is only 1.5 years old. Any ideas of what this is and how to fix it? Called manufacturer who states it was only covered for 1 year. It came with the house that I had built. I was under the impression they did the registering for me but come to find out they didn’t. No extended warranty was purchased, however, I can per the manufacturer after it’s fixed. Thanks

  8. I keep getting that and E8, the stove shuts down I have not found an answer as to why not how to fix ut. If anyone has answers or input it would be appreciated.

  9. Suzanne Guedea

    My Whirlpool gas range has F3 showing. We just replaced the oven sensor and it’s still showing F3. What gives?

  10. Barbara Almond

    My whirlpool oven has time appearing in blue.
    Then below. In red. cooktop on. Cooktop hot

    None of the heating elements are on and have not been on overnight. Is there a reset switch to flip to turn the constant lighting off?

  11. I just replaced the bottom element on my whirlpool range (YWFE510S0AS0) after it started sparking and crackling. It was harder than YouTube videos showed as one of the connectors had a very short wire and kept disappearing into the insulation. Now that I think I successfully reconnected it gives me an F9 error code. I can’t get into the test mode as I can hit cancel twice but start does nothing. I’ve reset the breaker panel and unplugged for 5 minutes but nothing works. The door lock seems fine. Any suggestions on what may be wrong ? Thank you

  12. The Self-Clean function on my Whirlpool Gold has not worked for several years. I accidentally hit the Clean button and the door locked, the oven does not heat to clean, and I cannot unlock the oven door. Otherwise, up to this point, every other function works fine.

  13. My oven wont heat nor will my stove top work. No error code and start button beeps 2 times any ideas?

  14. Whirlpool Range WEE740HOSO error code F8EO cooling fan turning to slow what can I do to fix the problem ?

  15. Jeffrey D Wingfield

    My stove is readimg f2 e1 and f3 eo what could be the issue we have already replace the sensor wire so what could be the problem because it’s still flashing error F3 EO and error f wanted you F2 E1

  16. Have a barely 6 month old Whirlpool stove, used broiler once and the next day have E R R, F1, F0 and oven won’t work..tried unplugging but still can’t use oven.

  17. Hi my whirlpool oven AMW 519/IX is not heating properly, the display shows Err 5 but can’t find this error code anywhere on internet.
    Any suggestions?

  18. I have a Whirlpool double oven the error code E2 F6 appears I reset the circuit breaker , and the stove works or if I hit the start button , then a hour later the code appears again what does this code mean ?

  19. We had a big thunder/lightning near our home. When this happened the Whirlpool stove beeped, a message of “keyboard disabled” came on and the lights inside the oven came on and did not go off. I unplugged the oven and plugged it back in but the same thing occurred. Is this fixable?

  20. What does a code E1 F1 mean on a Whirlpool gold glass top oven? After our power went out this showed up and the stove top works but the oven and clock display doesn’t.

  21. ALLEN VETTER - DIY Repair Assistant

    Bohdanna Hansen,
    Whirlpool oven code “d o o r” describes that there is an issue with the door.
    Be sure the door is closed.
    If closed, the door switch may have a fault.
    Remove power to the oven and test the door switch.
    -RR

  22. Bohdanna Hansen

    What does it mean when the letters “d o o r” come on when I try to push start???

  23. Whirlpool gas oven, 3 yrs old, error code F8E0 ‘cooling fan speed too low’
    What do we need to do?

  24. I have a Whirlpool built in double oven, model RBD305 PD3 Serial number
    XR3105657. At times an error code E6 F2 appears. Push Cancel and the
    code goes away and the oven works OK. What does the code mean and
    how do I fix it?
    Thank you
    Joe

  25. I have a whirpool range and when i want to bake i press bake and it says CLEAN it doesnt go in to bake. would it be the motherboard the problem?

  26. Elisa Jackson

    I have the exact same problem. I also have the cracks and actual chippinig of the enamel oven surface on the floor of the oven at the oven door opening. Have you ever gotten a response or solution to this issue. I want to clean my oven today, but I don’t want to make the chipping/cracking worse. Thank you.

  27. I have a Whirlpool self-cleaning accubake system with an error of e1 f7. Does anyone know what that means? It also beeps twice every time it comes on.

  28. i have a whirlpool range that the f1e3 code appears periodically can this be fixed by resetting the range

  29. I have a 2 yr old Whirlpool GoldStar series built-in oven/microwave combo. When using the self cleaning feature the error message “F5E4” appears near the end of the cleaning process. What does this mean and how can this be fixed? Thank you

  30. I have an gold series oven. we turn on the oven cleaning system and at the end its cycle an error code f5e4 came up. plus the bottom of the oven is all hair line/ spider web cracks plus its buckled up at one end?. this cant be normal? please advise. thank you I have picture’s of the error code and cracks.

  31. I have error code 5 coming up on my ikea whirlpool nutid mwc 6 microwave oven,any help on what this is,if its one of the boards need replacing which one.It only happens when I switch the micro wave on,regards simon.

  32. I have a Whirlpool range Model # YGY397LXUS04 with an error code of
    5a6 6ath or 5ab bath. Does anyone know what this means and how to correct/fix this?
    Thanks in advance, Dennis

  33. Have a whirlpool oven model# Rf111pxsq. Replace both broil element and bottom element. Turn oven on and oven heating light blinks once but no heat. Can someone tell me what’s wrong with it. And top burners work fine.

  34. Arlene Bloomquist

    My Whirlpool Range keeps showing an error code F1-E2 on the clock display and I have tried breaking the circuit and it has returned…What does this mean ? The oven and stovetop still are working perfectly ! Any other suggestions ? I cannot afford a new part and wonder if this is just something I can ignore !

  35. I was baking and everything was fine. Then the oven beeped and said there was an error– to press start and then cancel. Now I can’t turn on any of the oven settings. I get a message that says feature not available.

  36. The Whirlpool ceramic top range I bought used, Accubake. Stove top works fine oven does not. When I hit the start button for the oven there’s a question mark by it. ( start? )

  37. Tracy Stratton

    After a thunderstorm, our range display shows the word “hot” and will not do anything. The burners work but the oven light comes on but will not stay on, and all other buttons just beep when pushed.

    Is this fixable or did the lightening permanently damage the stove?

  38. David Schowalter

    Range Model# WFE710H0AH0 Oven would not heat over 280 degrees after 30 minutes, Auto Test read – F1 E0, I replaced the control unit #WPW10340304 from Appliance Pro, Oven still not heating past 200 degrees. Auto Test with new Control Unit now says: “1 Failure…. 0 Fault…. Check wiring DBL K1 or BAK K2 or Bake Element.
    What should I do, return new control unit and order the lower oven bake element?

  39. My whirlpool oven has stopped working and on the display it reads f of, I can’t find anything on internet to say what it means?

  40. I have a Whirlpool Gold self cleaning gas oven which is showing E6-F3 error code. I cleared it, but 10 minutes later it came back on

  41. My oven keeps saying “hot” when i try to bake stuff but its not hot. Is that an error code and how do I fix it?

  42. After an overnight power failure, awoke to Whirlpool oven clock 20 minutes FAST.
    Attempted to correct clock and it produced 5A6 error code.
    No controls worked.
    After turning off breaker for 10 minutes, panel displayed 30 for a few seconds then returned to 5A6.
    Appliance is Whirlpool slide-in oven about 5 years old.

  43. I put a meatloaf in the oven when suddenly the door locked, error code e2 f 3 appeared and then it said “self clean” so I hit cancel and “cool” came on. We shut off the power but after an hour the door still wouldn’t open. My meatloaf is still in the oven and I can’t get it out. We don’t dare turn the power back on as it stays locked and starts heating up again! What can I do?

  44. Have a Whirlpool range model# wee740hoso with error code F8EO.
    The fan is turning too slow.
    What do I do to fix this problem?
    I’ve turned it off for 5 mins and code clears but as soon as I try to use the oven it returns.

  45. Both of the oven bake elements are missing in my wall double-oven, will this cause an error code of E6 F2 on the display panel?

  46. I started the self clean option on my Whirlpool range (about 8yrs old). I went back later to find the door ajar, and the lock out, but not engaged in the door. I have the E0 F5 error. Is there any way to clear this and disengage the lock.

Leave a Comment

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.