Home » Home DIY Repair » Washing Machine Repair » Whirlpool Duet Washer Error Code E01 F09 – How To Fix – How To Clear?

Whirlpool Duet Washer Error Code E01 F09 – How To Fix – How To Clear?

Whirlpool Duet Washer Error Code E01 F09! I have a Whirlpool Duet washing machine and I constantly get the E01 F09 error code with any wash cycle. I have tried running a diagnostic test on it but I could not get it to work. I have cleaned and checked the pressure switch and the drain pump and both seem to be visually good. What does the error code E01 F09 mean on my Whirlpool Duet Washing Machine?

Whirlpool Washer Control Panel DiagramWhirlpool Washer Control Panel Diagram

Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME.

When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water. This means there is a possible fault in the Drain pump, Pressure Switch, or the Electronic Control Board – CCU. Follow the instructions below as the error code may be coming up because a part is bent, clogged or needs to be resecured or cleaned out.

Whirlpool Washer Error Code E01 - F9E1Whirlpool Washer Error Code E01 – F9E1 – Fix Repair – Clear Error Code

– If you use the wrong detergent, SUDS can cause a delay in draining out the water and the error code can display.
– Your Whirlpool washer will drain for 4 minutes then pause for 5 minutes.
– Your washer will then try to drain 4 for additional minutes.
– F9E1 or E01 F09 will display if the Whirlpool washer does not drain.

A Whirlpool Duet Washing Machine SHOULD drain out the water in approximately 2 minutes or less when running normally with no issues.

Whirlpool Washer DUET - PDF TECH SHEET FOR REPAIRHere is the full Whirlpool Washer Tech Sheet in PDF for download.

Here are some reasons the Whirlpool Washer Error Code E01 F09 will display:

1 – You may have a drain hose that is bent and not letting the water drain out – Check the back of the washer.
2 – Be certain the drain hose height does not exceed 96″ or the washer cannot drain properly.
3 – Clean the drain pump filter on the bottom front of the washer of any particles or objects.
4 – Check the connections to be sure they are secure from the tub to the air trap – air trap to pressure hose – pressure hose to pressure sensor.
5 – Follow TEST #8 to see if the Drain Pump is working properly.

Whirlpool Washer Drain Pump Test 1Whirlpool Washer Drain Pump Test 2Whirlpool Washer Drain Pump Test 3Whirlpool Washer Drain Pump Test 4DRAIN PUMP TEST FOR WHIRLPOOL DUET WASHERS

 

Whirlpool Washer Drain Pump ReplacementWhirlpool Washer Drain Pump Replacement

6 – Is the pressure switch hose pinched, clogged, or leaking air? – Be sure hose is clean and not bent.
7 – Be sure pressure switch is working and replace if part is faulty. – Use a multimeter to be sure.

Pressure Switch For Whirlpool Duet Washing Machine
Part Number WPW10304342 (AP6019132) replaces W10304342, PS11752436.

8 – Step #12 in TEST #8 states that if all the ohm tests and visual checks pass, then the problem is the CCU. Replace CCU/Whirlpool Duet Washing Machine Electronic Control Board.

Whirlpool Duet Washing Machine Electronic Control Board – CCU
Part Number W10427967 (AP5653804) replaces 12706109, 2683854, PS5573780, W10153959, W10354085, W10384503, W10388202, W10406632.

How to go into DIAGNOSTIC TEST MODE with Whirlpool Duet Washer:

The images below explain diagnostic mode and how to use it to find the issue with your washer…

Whirlpool Washer Diagnostic Test 1Whirlpool Washer Diagnostic Test 2Whirlpool Washer Diagnostic Test 3Whirlpool Washer Diagnostic Test Chart

 

Whirlpool Washer DUET - PDF TECH SHEET FOR REPAIRHere is the full Whirlpool Washer Tech Sheet in PDF for download.

 


WHIRLPOOL DUET / MAYTAG WASHER MACHINE repair error codes F01, F06, E01, E02

Need help? Ask your question below and we will be happy to assist you with your Whirlpool Duet Washer with the E01, F06, F01, E02, error codes.

Leave a Reply

2 thoughts on “Whirlpool Duet Washer Error Code E01 F09 – How To Fix – How To Clear?”

  1. Maytag front loader –
    E01 F09 error codes repeatedly.
    Door lock button will not unlock even when error codes clear.

Leave a Comment

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.