Home » Home DIY Repair » Washing Machine Repair » Frigidaire Affinity Front Load Washing Machine Error Fault Codes

Frigidaire Affinity Front Load Washing Machine Error Fault Codes

Frigidaire Affinity Front Load Washing Machine Error Fault Codes. Here is information that will assist you in identifying what may be making your Frigidaire affinity front load washer display an error code. Identifying what the error or fault code is will help you to repair your washer. The Frigidaire specific error fault codes below are to give you an idea as to what part is at fault. You may have to do further troubleshooting to find what may be causing the fault for that specific part.

Frigidaire Washing Machine Error Codes

FRIGIDAIRE Washing Machine Error/Fault Codes – Probable Fault Identifiers

Frigidaire Affinity Front Load Washer Error CodesFrigidaire Affinity Front Load Washer Error Codes 1

 

Frigidaire Washer Error Code Chart 2Frigidaire Washer Error Code Chart 2

 

Frigidaire Washer Error Code Chart Test 1Frigidaire Washer Error Code Chart Test 1

 

Frigidaire Washer Error Code Chart Test 2Frigidaire Washer Error Code Chart Test 2

 

Frigidaire Front Load Washer Error Codes

E11
Fill time too long
CHECK: Water inlet valve assembly

E13
Water leak in tub or air leak in air bell
CHECK: Outer wash tub, Air hose, Water-level pressure switch

E21
Water not pumping out fast enough
CHECK: Drain Pump

E23
Drain pump relay on control board failed or wire off pump
CHECK: Electronic control board

E24
Drain pump relay on control board failed or wire off pump
CHECK: Electronic control board

E31
Pressure sensor not communicating with control board
CHECK: Water level pressure sensor

E35
Pressure sensor indicates water overfill
CHECK: Water-level pressure sensor, Water inlet valve assembly

E36
Control board problem

E41
Control board thinks the door switch is open

E43
Control board problem

E44
Control board problem

E45
Control board problem

E46
Control board problem

E47
Board thinks the door PTC circuit is open in spin
CHECK: Door lock/switch assembly, Wiring harness

E48
Board thinks the door PTC circuit is closed
CHECK: Door lock/switch assembly, Wiring harness

E52
Bad signal from generator
CHECK: Drive motor, Speed control board

E56
High motor current
CHECK: Drive motor, Outer tub, Spin basket, Speed control board

E57
High current on motor phase
CHECK: Drive motor, Outer tub, Spin basket, Speed control board

E59
No signal for 3 seconds
CHECK: Drive motor, Outer tub, Spin basket, Speed control board

E5A
High temp on heat sink caused by overloading

E5B
High temp on heat sink

E5C
High temp on heat sink

E5D
Communication problem

E5E
Communication problem

E5F
Communication problem

E66
Heating element relay failure

E67
Input voltage on microprocessor incorrect

E68
Current leakage to ground on heater or fuse opened

E70
The control board is not seeing the correct water supply

E71
Wash NTC failure

E74
Wash temperature does not increase

E75
Water temperature sensor circuit

E76
NTC temperature for the cold water valve over the limits

E82
Console control problem

E83
Console control problem

E91
Communication error between UI board and control board

E93
Console control problem

E94
Console control problem

E95
Communication error

E97
Console control problem

E98
Console control problem

EB1
Incoming power frequency out of limits

EB2
Incoming line voltage above 130 VAC

EB3
Incoming line voltage below 90 VAC

EF1
Clogged drain pump

EF2
Too much soap

EBE
Console control problem

EBF
Console control problem

EF5
NTC temperature for the hot water valve over the limits

If your Frigidaire Washing Machine Error Code is not listed here, check
Google or YouTube to find the exact error code your Frigidaire washer is displaying.

NEED WASHER PARTS? Over 6,000 New and Discounted Washing
Machine Replacement Parts For ALL Washing Machine Models

Here are error codes for Amana, Asko, Beko, Bosch, Daewoo, Fisher & Paykel, Frigidaire,
GE, Haier, Hotpoint, Kenmore, LG, Maytag, Samsung, and Whirlpool washers.
Here are Washing Machine Error Codes For All Washing Machines.

Need assistance with finding an error code for your washer?
Ask your question below and we will be happy to assist.

Leave a Reply

44 thoughts on “Frigidaire Affinity Front Load Washing Machine Error Fault Codes”

  1. My frigidaire front load is washing for five minutes and then all the lights go out and unable to restart then e91 is displayed. I tried to reset by unplugging for 30 minutes but no success

  2. My model number is fafw3921nw0, and I’m receiving the same error code E32. It won’t add water, or spin. And I only received the code when I held the Start/Pause, and Cancel buttons for it to show me the code. According to the chart above, this code doesn’t even exist

  3. Electrolux Frigidaire Refrigerator Affinity Model LTF6000FSO – year 05/07
    When it powers on, it says ERR and no error codes.
    Won’t go into diagnostic mode and wont show any error codes.
    Just keeps saying ERR.
    Sometimes it will scroll through the adjust temp settings when you press the start button, other times it just shows ERR and all Adjust temp settings flash on and off.
    I’ve reset it at the circuit breaker and the same issue keeps happening.

  4. I have a frigidaire affinity and I cant seem to figure out what is wrongi get no error codes just Err I have tried to reset, i have unplugged and i even unplugged the connections to the door mechanism and I still get same results any help would be great thanks

  5. Steven Henry Tenhundfeld

    Have A Frigidaire Mod LTF2940eSo purchased 06/05
    Have Error code E61 this code is not in my tech data sheet
    What does it tell you ?

  6. I’ve replaced the motor control board on the Frigidaire affinity washer, and now is giving me E99. I can’t find what is E99 error code is. Do anyone know how to fix this code?

  7. Washing machine won’t final spin in normal cycle mode so clothes are dripping and water in bottom.
    I run spin to drain and it works and then re spin out the clothes in small batches after wringing out first.
    The quick cycle usually works.
    My latch broke and replaced.
    No error codes.
    Have replaced pump along with cleaning out the drain.
    Use to say PAU before latch replaced.
    Now won’t final spin on normal cycle.

  8. I have a frigidaire affinity, it starts filling, fills about 5 seconds then stops for a few minutes.
    Then does it all over again.
    I pulled the code and it says E5E.
    I looked at the fault code table and it says “communication error see test 11”

  9. DIY Project Help Tips

    Mary,
    If your Frigidaire Affinity Front Load Washing Machine is stuck on pause, try unplugging the washer for 10 minutes to attempt to reset it.
    It that does not solve it, then you may have a faulty board or other issue in your washer (possibly mechanical).
    What is the model number?
    -RR

  10. I have a 4 year old Frigidaire Affinity Front Loader FAFs4073NW0, that was emitting error code E59, so I replaced the motor control board and wire harness, and ohmed out the motor to ensure working properly.
    Now, when I attempt to wash a load from any of the selections, the machine fills with water, sits for 15 minutes or so with no tub motion, then emits code E59.
    I then clear the error codes once, maybe twice, then the machine runs like normal for multiple loads. Once it goes cold for a day or so, i have to start the process all over.

  11. Charles Champagne

    I have a Frigidaire Front load Affinity washer FAFS4073NW0, 4 years old, and when I select a wash cycle it fills with water, sits for about 15 minutes with no tub motion, then emits error code E59.
    I then have to clear the error codes at least once, maybe twice, then it runs like it is supposed to for multiple washes.
    I have replaced the motor control board and wire harness, and ohmed out the motor.

  12. I have a frigidaire affinity front load washing machine error code eb1 or e61 that open and close by itself

  13. Replace the door switch. I had the same problem on my Frigidaire front load washer. I purchased a new door switch on EBay for less than $30 including shipping and handling. You can also search YouTube to view the part switch out. A very simple process. I had the same error code and it solved my problem. Good luck.

  14. I have a Frigidaire Affinity front load washer (fafw3801lw3).
    I’ve replaced the door lock.
    But now when i try to start the washer, with or without any clothes in it, i get the time of the wash cycle and PAU, blinking back and forth.
    The door lock light doesn’t light up and i don’t hear the door lock neither.
    I have no idea on what to do next to get my washer working.

  15. I receive error code E41 on my Frigidaire front load washer model LTF6000ES1. What is the problem and how do I fix it ?

  16. I have an affinity washer with an e55 error code.
    I changed out the motor but it’s still doing the same thing!

  17. My husband has repaired our washing machine however, ALL cycle lights are lit and says error across the display screen and I’M TRYING to reset it having NO KNOWLEDGE.
    I have TRIED every combination of buttons being held that I could find!
    It is a Frigidaire affinity front loader washer.

  18. DIY Project Help Tips

    Sandy Lawson,
    Frigidaire Front Load Washer error code e90 will come up when the washing machine electronics get wet.
    E90 can also happen if wet clothes are left in the washer for a long time.
    If you keep getting error code E90 = Reset the controls.
    Press and hold the “cancel” button for 20 seconds then try to set a new wash cycle and press “start”.
    If the reset doesn’t work… unplug the washer for 10 minutes to reset it.
    If the e90 error comes back, replace the main control board.
    -RR

  19. Frigidaire front load washer #FAW3577KW – HAS ERROR CODE E90 and cannot find any such code listed. What is wrong?

  20. DIY Project Help Tips

    Gloria,
    On your Frigidaire washer, is there an “E” before the error code?
    We have E error codes but if those, either S4 or 54 appeared without the E in front of it, it may mean something different.
    Please confirm.
    What exactly is the washer doing?
    At what point does the error show up?
    -RR

  21. DIY Project Help Tips

    Victoria,
    Try unplugging the washer for 5 minutes and see if that may reset the ERR code. If you have issues with error codes appearing after you plug it back in, please let us know. Also include the model number of your washer.
    -RR

  22. I have a front loading Frigidaire washing machine and there are no numbers with the error code. All it says is Err. Wont do anything at all, just keeps beeping and all the lights flash, thats it.

  23. DIY Project Help Tips

    Justin,
    Frigidaire front load washer Error Code E31 = Pressure sensor not communicating with electronic control board.
    Unplug the washer and check the wire harness connections between the water level pressure sensor and the control board. If the wiring connections are okay, the water level pressure sensor usually needs to be replaced.
    -RR

  24. I have a Frigidaire front load washer ATF6500GG0. It fills with water and stops, error code 31. Where should I start troubleshooting? All help is appreciated.

  25. DIY Project Help Tips

    Victoria C,
    Make sure the wiring is correct after replacing the door lock switch, as this may have shorted something. Unplug washer and reset the breaker to the washer outlet. Check wiring to door switch.

    The E91 error code is signaling an issue with the User Interface board that has all of the indicator lights on it. A connector has likely become unplugged. Remove the screws from the rear of the top panel and inspect all of the wire connections near the front control assembly. Be sure to unplug the washer before removing the top. If you still have further issues the next step is to replace the User Interface Board.
    -RR

  26. VICTORIA CATCHINGS

    Frigidaire affinity model fafw411wL0 wasn’t spinning all the water out. I replaced it with a door lock switch and when i tried to test it i think it blew a fuse. The socket does not work anymore and none of the LED light up on the display lights. It says e91. Could someone help me out here?

  27. DIY Project Help Tips

    Tran,
    Is the washer adding water or spinning? Do you have an exact model number for us? At what point do you get the E32 error code?
    -RR

  28. So I had to just finally just call someone to come fix it. Which will happen in a couple days.
    However to answer your question and potentially aid others. To get the unit to drain, I unplugged it for about 10 seconds, rotated the dial to drain, and depressed both the start button and select button and the drain cycle worked as advertised.

  29. DIY Project Help Tips

    Toby,
    Have you checked that the drain pump is operating normally? It may be clogged, jammed or bad. Also look at the drain hose. When you say you were able to get it on the drain cycle, can you explain what you did to get it into the drain cycle? It may give us more clues as to what is going on in the washer at that point.
    -RR

  30. So at the end of the wash cycle, the tub does not empty and the washer turns off. Still full of water. I was able to get it on a drain cycle, but once I go to start a new load, ground hog day.
    Model number FAHE4044MW

  31. DIY Project Help Tips

    Toby,
    Can you tell us the symptoms of your washer? What stage was it in when it displayed the F8 error code? Wash, rinse, agitate, drain? Also can we have a model number to assist you further?
    -RR

  32. DIY Project Help Tips

    Phil,
    Can you please recheck error code? E3a is not in our database of Washer Error Codes for Frigidaire.
    -RR

  33. My Frigidaire Front Load Washer Keeps Saying Door Is Open. The Code Was E3a Saying Low Voltage. What Should I Do To Fix It?

  34. DIY Project Help Tips

    Leon,
    First of all be sure it is on the correct cycle.
    Does this happen with a full load and partial load of clothing?
    Does it seem as if the RPM of the drum is fast enough?
    You may need to take the washer apart and check out the counterweight and springs.
    Your tub may not be aligned properly.
    Here is a parts list for your Frigidaire Washer Tub that may assist you with the parts you need to check or replace.
    -RR

  35. Model Frigidaire fafw3801lw3
    MY WASHER IS NOT SPINNING STRONG ENOUGH. WHEN IT FINISHES ITS CYCLE, THE CLOTHES ARE STILL VERY WET.
    I PLACED IT ON RINSE N SPIN CYCLE, BUT TO NO-AVAIL, THE CLOTHES ARE STILL HEAVILY WET. THE SWITCH WOULDN’T ALLOW ME TO CANCEL CYCLE EITHER.

  36. DIY Project Help Tips

    Phyllis,
    D6 error code on a Frigidaire washing machine is not a valid error code. Are you sure it is not F6?
    -RR

  37. I have a D6 error on my Frigidare top load washing machine. I can not find my manual.
    The model number is fwac16h3msgks

Leave a Comment

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.