Home » Home DIY Repair » Washing Machine Repair » Fisher & Paykel AquaSmart Top Load Washing Machine Error Codes

Fisher & Paykel AquaSmart Top Load Washing Machine Error Codes

Fisher & Paykel Washing Machine is displaying an Error Code? Here is information that will assist you in identifying what may be making your Fisher & Paykel washing machine display an error code. Identifying what the error or fault code is will help you to repair your washer. The Fisher & Paykel AquaSmart error fault codes below are to give you an idea as to what part is at fault. These Fisher & Paykel error codes may not apply to all Fisher & Paykel washers. You may have to do further troubleshooting to find what may be causing the fault for that specific part. For more assistance finding the exact error on your washing machine, please ask a question below.

fisher paykel aquasmart washer error codesFisher & Paykel Aquasmart Top Load Washer Error Codes

Fisher Paykel Top-Load Washer Error Codes = Numbers 21, 26, 27, 49, 50, or 246.
Error Fault ConditionWater Inlet Valve Fault.
Repair or Check – Unplug the washer from power. Reconnect any non secure wires on the water inlet valve. Replace the wire harness if it is found to be damaged. If the wiring is okay then measure the resistance of the water inlet valves using an ohm meter. If the resistance of each water inlet valve solenoid is not 60 to 62 ohms then replace the complete water inlet valve assembly.
Parts for Replacement – Water Inlet Valve Assembly or Wire Harness.

Fisher Paykel Top-Load Washer Error Codes = Numbers 38 or 39.
Error Fault ConditionWater Level Pressure Transducer Air Tube Fault.
Repair or Check – Unplug the washer from power. Reconnect the water level pressure switch air tube. Replace the air tube if it is found to be damaged.
Parts for Replacement – Water Level Pressure Switch Air Tube.

Fisher Paykel Top-Load Washer Error Codes = Numbers 58 or 68.
Error Fault ConditionWater Level Pressure Transducer Fault.
Repair or Check – The water level pressure transducer is in the motor control module. Unplug the washer from power and replace the motor control module.
Parts for Replacement – Motor Control Module.

Fisher Paykel Top-Load Washer Error Codes = Numbers 10, 41, or 237.
Error Fault ConditionThermistor aka = Water Temperature Sensor Fault.
Repair or Check – Unplug the washing machine from power. Reconnect any unsecured wires in the thermistor circuit. Replace the wire harness if it is found to be damaged. Measure the thermistor resistance using a ohm meter. Replace the thermistor if the resistance is not 12.5K ohms at 68 degrees Fahrenheit.
Parts for Replacement – Thermistor or Wire Harness.

Fisher Paykel Top-Load Washer Error Codes = Numbers 1, 57, 60, 107, 108, 112, 133, 220, 221, 222, 223, 224, 225, 226, 230, 232, 233, 236, 241, 243, 252, or 254.
Error Fault ConditionMotor Control Module Fault.
Repair or Check – Unplug the washer from power. Replace the motor control module.
Parts for Replacement – Motor Control Module.

Fisher Paykel Top-Load Washer Error Codes = Numbers 45, 46, 103, 104, 105, 106, or 241.
Error Fault ConditionDisplay Module Fault.
Repair or Check – Unplug the washing machine from power. Replace the display module.
Parts for Replacement – Display Module.

Fisher Paykel Top-Load Washer Error Codes = Numbers 234, 235, 238, or 239.
Error Fault ConditionLid Lock is Bad.
Repair or Check – Unplug the washer and reconnect any loose wires from the lid lock assembly. Replace the wire harness if it is found to be damaged. Measure the resistance of the lid lock using a volt/ohm meter. If the resistance is not 62 to 64 ohms then replace the lid lock assembly. If the resistance is found to be in the correct range then replace the motor control module.
Parts for Replacement – Lid Lock Assembly or Wire Harness or Motor Control Module.

Fisher Paykel Top-Load Washer Error Codes = Numbers 40, 56, or 160.
Error Fault ConditionSpin Basket Will Not Engage Or Disengage From Clutch.
Repair or Check – The spin basket has to be able to rise and fall with the water level. This is to engage and disengage from the clutch. Unplug the washer from power. Remove the spin basket. Remove any objects found between the spin basket and the tub. An object could be interfering with the spin basket clutch engagement. Replace any broken drive components.
Parts for Replacement – Drive Components.

Fisher Paykel Top-Load Washer Error Codes = Numbers 136 or 137.
Error Fault ConditionMotor Is Not Running.
Repair or Check – Unplug the washer from power. Rotate the spin basket by hand. If the spin basket will not rotate freely by hand then remove any objects between the spin basket and tub. If the spin basket rotates freely by hand then replace the drive motor as it is most likely defective. If the problem keeps happening then replace the motor control module.
Parts for Replacement – Drive Motor or Motor Control Module.

Fisher Paykel Top-Load Washer Error Codes = Numbers 37, 114, 245, 247, 248, 249, 250, or 253.
Error Fault ConditionWater Is Not Draining.
Repair or Check – Remove any clogs from homes drain that is used for the washer. Remove any clogs or bends from the washers draining hose. Unplug the washer from power and check the drain pump for a blockage. If the drain pump is defective it will need to be replaced.
Parts for Replacement – Drain Pump.

fisher & paykel aquasmart washing machine error codesFisher & Paykel Aquasmart washing machine error codes list

fisher and paykel washer NEW fault codesFisher and Paykel washer NEW fault codes

fisher and paykel washer diagnostic modeFisher and Paykel washing machine = Diagnostic mode

If your Fisher & Paykel Washing Machine Error Code is not listed here, check
Google or YouTube to find the exact error code your Fisher & Paykel is displaying.

Here are error codes for Amana, Asko, Beko, Bosch, Daewoo, Fisher & Paykel, Frigidaire,
GE, Haier, Hotpoint, Kenmore, LG, Maytag, Samsung, and Whirlpool washers.
Here are Washing Machine Error Codes For All Washing Machines.

fisher & paykel replacement parts washersNEED Fisher & Paykel WASHER PARTS? New and Discounted
Washing Machine Replacement Parts For ALL Washing Machine Models

Need assistance with finding an error code for your Fisher & Paykel washer? Ask your question below and we will be happy to assist.

Leave a Reply

35 thoughts on “Fisher & Paykel AquaSmart Top Load Washing Machine Error Codes”

  1. Fisher and Paykel WL26CW1 error code 57
    Motor control module?
    Are there replacement parts available?
    Can’t find a Fisher and Paykel service rep within 100 miles.

  2. same code as Jolene. 11111000 flashing. 1st light red, then 4 green, rest off. will not advance cycles unless buttons are pushed. takes 4 hrs to wash!!!!!

  3. I have a Fisher and Paykel washing machine WL80T65C displaying error 49. I have checked the water inlet valves and measured the resistance of the solenoids, the resistance was between 50 and 55 ohms, and this should be between 60 and 62 ohms, therefore I replaced the valves, I still have the same error 49. where could the problem be?

  4. F&P top loader WL80T65CW1 seems to run OK but doesn’t advance through cycles properly. It was on the wash part of the Regular cycle for 90 minutes last night (the count down timer showed 35 minutes to go throughout this time), and the claimed 9 minute spin cycle for 120 minutes (I forgot to come back and check it). It shows an error code 136 from 6 washes ago because I did have a very unbalanced load, but no other error codes. Can turn on all functions manually, e.g. spin, drain, fabric softener, etc. Any help appreciated!

  5. Fisher Pakel shows error 40, can I reset the washing machine? I need to know what error 40 is before I can call a service technician.

  6. Hi I have a Fisher & P top loader washing machine. I moved it a little to get access to replace taps on wall. Now it will not allow cold water to enter machine. Hot is ok. however will not rinse unless it is with hot water. I believe it is error code 3 . is there a reset button . I think code says motor controller fault but seems strange all else is working . any ideas

  7. William Smallwood

    I have a aquasmart top load washing machine, WL80T65D, it won’t progress past rinse cycle unless you manually do it, the regular light setting light is on as is the softener off and the cold light on, the fast and rinse lights are flashing, does this mean that the board needs replacing?? Regards, Will.

  8. We have an Fisher Paykel MW512AU top loader Washing machine.
    Had error code 49 with bad cold water inlet valve.
    Replaced with good one but error code still present.
    Is there a reset or something else to check please?

  9. Fisher and paykel aquasmart model WL70T60D has an error and won’t start or fill, it starts beeping after a few seconds after pressing the Start button, then only the Delicates, sheets and high efficiency buttons are illuminated. What is this error?

  10. I just purchased a F&P top loader. I did the installation and it stops when it says no drn connection. Water has drained out of tub and goes down the drain. Anyone know what may be causing this? Brand new. Can’t wash my clothes. Thanks.

  11. I have a aquasmart model WL70T60D. I think my housemate put it in diagnostic mode but unsure. essentially the lights that are illuminated are ‘delicates’, ‘sheets’ and ‘high efficiency’. I think this might be error code 40 something but I have no idea. Any help?

  12. DIY Project Help Tips

    Kim,
    The FIsher and Paykel Error Code 104 is a communication error between the display PCB and the main controller PCB.
    This can be caused by a faulty display pcb, faulty main controller PCB, faulty drain pump or faulty RPS on motor.
    -RR

  13. My top loading machine has an error code of 104.
    Earlier I had a 62 I think or 64 which sounded like pump issue (won’t drain after first wash).
    Any clues please?

  14. I have a top loading Fisher & Paykel washer-Intuitive eco that just started beeping in the middle of the night with an error code #28. I had not used it for days and it just errored out. Unplugged it and tried to use it today and it will only fill with cold water. Can you help me with this problem? I cannot use warm or hot water.

  15. I have an error on the F and P Fisher and Paykel aquasmart, which does not have a number, it appears as a small wrench.
    I’ve turned the power off at the switch and left it off for a period of time.
    The wash does not seem to drain the water.
    It beeps constantly along with this wrench sign.

  16. fisher paykel model GWL15 ECOSMART error code 00000111 = 7 but can’t seem to find that code. Beeps on rinse cycle and will not advance unless i cycle to spin.

  17. DIY Project Help Tips

    Lorraine Beasley,
    First, we would call back the appliance repair company and tell them what they diagnosed and replaced has caused another washer error.
    Let them know you have error code 51.
    Here is information we have for that specific error code on your washer…

    Fisher & Paykel Washing machine error code 51 = Diverter valve timeout fault
    The machine has detected that the diverter valve is leaking water to the drain when it should be recirculating.
    Check by waiting for re-circulating function and checking if water is coming from the drain hose.

    Primary source – Diverter valve
    Check diverter valve continuity. If open circuit, replace diverter valve.

    Secondary check Motor Controller Module (drive circuitry blown).
    Replace Motor Controller Module.

    Third source – Diverter valve harness wire connectors.
    Replace bowl harness.

    -RR

  18. Lorraine Beasley

    I have a Fisher and Paykel Intuitive eco washing machine which is giving me a Service code Error 51.
    What does this mean.
    I spent money in repairs yesterday when it gave me Service Code Error 39.
    The pump and valve were changed.
    Now I am getting error 51.
    Thank you for your help!

  19. DIY Project Help Tips

    Nuala Jewitt,
    Error Code 9 on Fisher and Paykel Aquasmart = Size setting error.
    If this appears it will be necessary to set the size of the Aquasmart:

    1. Press and hold the SPIN button, then press the POWER button until three beeps are heard.
    2. Press the FABRIC SOFTENER button once to size the machine.
    3. Press the POWER button.

    -RR

  20. I have error code 9 on a WL70T60C Fisher and Paykel Aquasmart. What is this?

  21. DIY Project Help Tips

    Jacqui,
    The 68 F&P washer error code is an indication of a bad lid lock switch.
    Try the diagnostics error code check.

    Or set the machine to another cycle and press start and see when it stops?
    Then tell me what lights are lit?
    If it does come back with the lights again then I would check to see if you can open the lid while it is supposed to be locked?
    If you can open the lid or you think the lid switch is bad or not seating correctly then I would replace it.
    -RR

  22. I have a F and P Smart Drive 8 top loader washing machine – model LW085F that suddenly would not start. All other controls work – temp, load size, spin speed etc.
    Using the binary number on a 7 light panel for the wash cycle shows error code 68. ie… light 3 and 7 light up. Can anyone advise what this means on this model?
    It is a very old machine but have never had a problem. Not sure if worth getting F and P out to repair.

  23. DIY Project Help Tips

    Helen,
    Is your AquaSmart washer on level ground?
    What happens if you run an empty load, does it jump around?
    You may have a spring or a tub balancer that has fallen off or is loose.
    Check the outer drum to see if that is the case.
    -RR

  24. Similar to 3 above. My AquaSmart clothes washer model # WLTOT60DW1 gets very unbalanced in spin cycle. It spins for a little while then machine jumps around the floor, sometimes self correcting then spins again, sometimes beeping but regardless of whether or not I rearrange the clothes it will spin a little then repeats whole process. The clothes are still very wet when I give up and remove them. Any ideas?

  25. DIY Project Help Tips

    David Forsyth,

    FISHER AND PAYKEL DRYER ERROR CODE 9: EXHAUST SENSOR UNDER TEMPERATURE
    The exhaust sensor measures under temperature (open circuit or not plugged in)

    TO FIX ERROR CODE 9:
    Check the integrity of the sensor circuit checking particularly for short circuits.
    Replace thermistor and harness if out of range.
    Check the element integrity in that it switches off when the dryer is stopped.
    Replace the motor control module.
    Replace the sensor module.
    -RR

  26. I have a Dryer. It is a Fisher & Paykel Aerosmart
    Model: DG27CW1
    S/N: LEU309983
    It shows “Error Code 9”
    Can you tell me what that error means?

  27. DIY Project Help Tips

    Coral Venn,
    Can you supply us with the model number of your Fisher & Paykel Washing machine? This will give us a better idea of what may need to be replaced. What exactly happens to your washer? It goes offline as in it has NO POWER? Or the washer sits in the middle of a cycle and does nothing? Are the lights on the washer still illuminated when this issue happens? Any error codes present?
    -RR

  28. FP Aqua smart machine, when machine gets to spin cycle it goes off line. Have tried to even arrange weight evenly to no avail. Have tried to spin empty with just water… still the same. Have leveled the machine still the same. Ready to toss it out the window, have you any suggestions please?

  29. DIY Project Help Tips

    Michael,
    Fisher Paykel Error code 9 means the washer needs to be reset to size. To correct error code 9….
    1 – Turn the machine off using the Power button.
    2 – Hold down the Left Scroll button and press the Start/Pause button. This will bring up a screen for setting the size of the machine.
    3 – Use the scroll buttons to choose the appropriate value. Start with the size 650 and if that does not work, try different size settings.
    4 – Once you have your size setting, press the Power button to save the setting and exit.
    -RR

  30. Have changed the control panel 421232nap on my Fisher & Paykel washer. After it fill with water, I am getting fault code 9. How do I reset it? I’m a retired TV tech and this was only problem I found. Many thanks in advance!

  31. DIY Project Help Tips

    Betsy,
    It should take only a few minutes under normal circumstances. The installation test cycle just checks to see if there are any errors or faults in the system. If it is taking a long time, are there any error codes displayed?

    Fisher & Paykel Washing Machine Installation test cycle…
    Your washer must be correctly installed before use. Check the machine’s installation and operation using the following procedure:
    1 – Touch POWER to activate your washer.
    2 – Touch both the KEYLOCK and OPTIONS buttons at the same time, and hold for three seconds.
    3 – Touch START/PAUSE to start the installation test cycle.
    4 – The machine will beep to signal the end of the installation test cycle. Any faults will be displayed on the screen.
    Note: if there are no faults found, the washer will automatically turn off at the end of the installation test cycle.
    -RR

Leave a Comment

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.