Home » Home DIY Repair » Clothes Dryer Repair » Maytag Bravos Dryer Error Codes – How To Clear

Maytag Bravos Dryer Error Codes – How To Clear

Maytag Bravos dryer error codes are shown on your dryers display to help you troubleshoot the problem with your dryer. Our error codes below will help you to identify what is wrong with your Maytag Bravos dryer. Once you have identified the error code, this will tell you which part is causing the issue. You can then check the part in question and clean or replace it if needed. Maytag Bravos dryer help videos are here if needed.

Maytag bravos dryer error codesMaytag bravos dryer error codes

Maytag Bravos Dryer Error Code = PF
Error Condition = Power Failure
Check or Repair Needed = Power failure while the dryer was in cycle. Press the Stop button to clear the display. If you experience common power failures on your dryer be sure to check the electrical outlet cord.
Replacement Parts = Outlet Cord

Maytag Bravos Dryer Error Code = F01
Error Condition = Main Electronic Control Board Fail
Check or Repair Needed = Remove the dryer from power for 10 minutes. Apply power back to the dryer and if the code returns you need to replace the main electronic control board.
Replacement Parts = Main Electronic Control Board

Maytag Bravos Dryer Error Code = F02
Error Condition = Keypad or User Interface Fail
Check or Repair Needed = A button on the keypad may be stuck on one of the user interface controls. If the button cannot be unstuck then replace the user interface control assembly.
Replacement Parts = User Interface Control Assembly

Maytag Bravos Dryer Error Code = F22
Error Condition = Exhaust Thermistor (Temp Sensor) Fail
Check or Repair Needed = Remove power from the dryer. Use a multi-meter and check the resistance of the thermistor (0,000 ohms). If the thermistor is bad then replace it.
Replacement Parts = Thermistor (Temp Sensor)

Maytag Bravos Dryer Error Code = F23
Error Condition = Exhaust Thermistor (Temp Sensor) Fail
Check or Repair Needed = Remove power from the dryer. Use a multi-meter and check the resistance of the thermistor (0,000 ohms). If the thermistor is bad then replace it.
Replacement Parts = Thermistor (Temp Sensor)

Maytag Bravos Dryer Error Code = F26
Error Condition = Drive Motor Fail
Check or Repair Needed = Remove power from the dryer. Check wiring connections between the main electronic control board and the drive motor. If the wiring connections are not damaged and connected then replace the drive motor.
Replacement Parts = Drive Motor

Maytag Bravos Dryer Error Code = F28
Error Condition = Moisture Sensor Fail
Check or Repair Needed = Remove power from the dryer. Check the wiring harness on the moisture sensor visually and with a multi-meter. If the wiring connections are okay then replace the moisture sensor.
Replacement Parts = Moisture Sensor

Maytag Bravos Dryer Error Code = F29
Error Condition = Moisture Sensor Fail
Check or Repair Needed = Remove power from the dryer. Check the wiring harness on the moisture sensor visually and with a multi-meter. If the wiring connections are okay then replace the moisture sensor.
Replacement Parts = Moisture Sensor

Maytag Bravos dryer error code chartMaytag Bravos dryer error code chart

 

Maytag Dryer PartsMaytag Dryer Parts

More clothes dryer troubleshooting for Frigidaire Dryer Error Codes, GE Dryer Error Codes, Kenmore Dryer Error Codes, LG Dryer Error Codes, Maytag Dryer Error Codes, Samsung Dryer Error Codes, and Whirlpool Dryer Error Codes.

If your Maytag Bravos Dryer error code is not listed here or you have issues with any Maytag Bravos Dryer Error Code, please leave a comment below and we will be happy to assist you with your dryer error code problem. If you have a different Maytag Dryer, you can ask error code questions about that model dryer also and we can further assist.

Leave a Reply

25 thoughts on “Maytag Bravos Dryer Error Codes – How To Clear”

  1. Does anyone know what to do with error code FE1 on a Maytag Bravos quiet series 300 dryer?

  2. I have a Maytag gas dryer Bravos MCT we had a breaker trip and now the dryer won’t work power to the unit . Unplugged for an hour switch the breaker. But the error code is not in the manual

  3. Dryer code is F32. Then CO. Dryer model is MEDB850WQ0, serial # M03933499.
    All lights and bells work but will not start cycle when start is pressed.

  4. Have a Maytag bravos gas dryer. Had a power failure and dryer displayed code P73. Any ideas or suggestions. Won’t run or display time but the power light and start light are working.

  5. I have a Maytag Bravos 400 showing a F21 error code. We had a power outage last night and the dryer worked prior to the storm. It was not running at the time of outage. Any idea on this code? I can’t find anything.

  6. Natasha Richman

    This means Air Flow! The vent could be kinked or your duct work/vent to the outside could be clogged! I fixed both of those issues though and mine still throws the code! I’m at a loss!

  7. My maytag drier error code is F77, but there’s no where to find out what it means, and another error code saying CO. Please contact me back asap.

  8. I have a code of Fn3. What I have researched it says I need to have some one service it. I live a long way from town and no one is going to come this far to look at it. We could fix it if we know what the issue is. If you can help it would be appreciated. Thank you

  9. Rachel Anderson

    We have a Maytag Bravos that is not showing an error code but still doesn’t work. When turned on as usual, by pressing power, selecting the dryer setting (right now it’s a 24 minute rapid dry), pressing start and the dryer beeps when I press the button but will not spin. The light above “sensing” is lit and the timer counts down as if it’s running a normal load, but again it doesn’t spin. We’ve checked both buttons in the door lining and they’re fine and working. Any advice is greatly appreciated since it’s Saturday and we have work and school on Monday.

  10. Hi,
    My power went out briefly the other day. My dryer flashed what I believe was F73 exactly when the power returned. I have not been able to reproduce the code. My timer will not come on unless I turn the dial to steam. The dryer will not come on but all other lights and noises work. Any ideas?

  11. My bravos dryer when started stays on “sensing” for 30 seconds. It then repeatedly flashes a “F” then a “1” but will not run. The error codes listed in my owner’s manual and on the website identify a solid “F01” error code, but not an alternating “F” and “1”. Are they the same?

  12. Christopher Dale Heufelder

    We have the Bravos XL washer/dryer set, and our dryer is giving us from time to time codes e03/f03 alternating, and sometimes will not dry a load, but can restart and will continue to dry. Cannot find any info on these codes, other than maytag says when e code followed by f code to contact a maytag service person. Any help will be appreciated.

  13. Jack Schwartz

    Have a Maytag Bravos XL dryer that won’t run.
    I can’t figure out how to find the error codes.
    How do you get them to be displayed?

  14. I own a Maytag MVWB800VQ0 washer (8 years old).
    When I go into the diagnostic mode using the 3 seconds on 3 seconds off, 3 seconds on, 3 seconds off, 3 seconds on method, and after all the lights come on and the 88 appears, I get an error code that was stored in memory.
    The error was fixed and the machine runs fine now, but when I go into the diagnostic mode the error is still showing up.
    Unplugging the machine for 1/2 hour did not erase the stored error code.
    What button sequence do I need to use to erase all old stored error codes?
    How do I clear the stored error code in memory on this machine?

  15. My dryer is giving me the f51 error code. Can you please tell me what it means. It’s a Maytag bravos

  16. Our Maytag Bravos XL has not given us a code.
    It just has three orange dashes across the display window on half of the cycles.
    I is working on the others but the times seem off.
    Not sure how to re-set it as there is nothing in the manual.

  17. My dryer never quit so when I checked it was blinking 1:39 and clothes still wet. Smelled like it was getting hot and smelled moist.
    My son pulled it out, hose was clear. Will replace hose and hook back up, kind of cracked and pulled apart when checking it out.
    Not the typical codes listed so not sure. Will replace hose, hook back up and try it unless you have some suggestions.

  18. We have a Maytag dryer that is an older model, and the problem that we started having with it was that it didn’t heat the drum, so we took upon ourselves to change the thermal fuse. We replaced it, the drum cannot turn so now we’re having that issue.

  19. DIY Project Help Tips

    John Bowman,
    The error codes F:AO then CO you have on your Maytag Bravos Dryer are not common.
    Can you please supply us with the exact model number of your dryer so we may research this issue further?
    -RR

  20. On my Maytag Bravos Dryer, I get an error code F:AO then CO for the second code. Dryer will not start. Can’t find these codes anywhere. What are they? Can I clear the codes/reset the dryer and try again?

Leave a Comment

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.