Electrolux Dishwasher Error Codes – How To Clear – What To Check

Electrolux dishwasher flashing an error code? Electrolux dishwashers have built in diagnostic systems. If your dishwasher finds, sees, or detects a fault or error in the system, it will show an error or fault code. The error code will display where the usual numbers are on the display screen. When an error code is displayed, your dishwasher is telling you a specific fault. The error code will tell you which parts on your Electrolux dishwasher to replace or check. You can also Search YouTube for Electrolux Dishwasher Error Codes or get advice from your Electrolux dishwasher owners manual when your Electrolux Dishwasher Is Displaying An Error Code. NOTE: Before ordering any parts from the ones listed below, check that the parts will fit with your model number Electrolux dishwasher.

Electrolux dishwasher error codesElectrolux dishwasher error codes

Electrolux Dishwasher Error Code = Delay Lights Flashing
Fault Condition: Heating Element Fail (The water did not get to the proper temp after a certain amount of time)
Repair or Check: The heating element may have burned out. Test with a multimeter for continuity. If the heating element does not have continuity replace it.
Parts Required: Heating Element

Electrolux Dishwasher Error Code loc or LOC
Fault Condition: Door Is Locked
Repair or Check: Press and hold the AIR DRY pad button for 3 seconds while the door is latched (or door open on newer models). This will unlock the control pad and the light goes out. The unit will display the last cycle ran.

Electrolux dishwasher control pad panelElectrolux dishwasher control pad panel

Electrolux Dishwasher Error Code 01
Fault Condition: Water Leak Is Detected (Sensor under the dishwasher detected a leak)
Repair or Check: Remove power to the dishwasher. Check hoses, pumps, and tub to find the leak. Replace any parts leaking.
Parts Required: Drain Hose – Drain Pump – Recirculation Pump

Electrolux Dishwasher Error Code 02
Fault Condition: Thermistor Sensor Fail
Repair or Check: Remove power power to the dishwasher and check the thermistor sensor circuit wiring. If the wiring checks out then replace the thermistor sensor.
Parts Required: Thermistor Sensor

Electrolux Dishwasher Error Code 03
Fault Condition: Wash Motor Fail
Repair or Check: Remove power to the dishwasher. Inspect the wiring for the wash motor. If the wiring checks out then check for an blockage in the pump. Replace the wash motor if the pump is not blocked and the wiring checks out.
Parts Required: Wash Motor

Electrolux Dishwasher Error Code 04
Fault Condition: Upper Fan Fail
Repair or Check: Remove power to the dishwasher and check the wiring for the upper fan. If the wiring checks out then replace the upper fan.
Parts Required: Upper Fan

Electrolux Dishwasher Error Code 05
Fault Condition: Upper Fan/Vent Fail
Repair or Check: Remove power to the dishwasher and check the wiring for the upper fan vent. If the wiring checks out then replace the upper fan vent.
Parts Required: Upper Fan/Vent

Electrolux Dishwasher Error Code 06
Fault Condition: Lower Fan Fail
Repair or Check: Remove power to the dishwasher and check the wiring for the lower fan. If the wiring checks out then replace the lower fan.
Parts Required: Lower Fan

Electrolux Dishwasher Error Code 07
Fault Condition: Drain Valve Fail
Repair or Check: Remove power to the dishwasher and check the wiring for the drain valve. If the wiring checks out then replace the drain valve.
Parts Required: Drain Valve

Electrolux Dishwasher Error Code 08
Fault Condition: User Interface Control Fail
Repair or Check: A switch on the user interface is possibly defective. Replace the complete user interface.
Parts Required: User Interface Control

Electrolux Dishwasher Error Code 09
Fault Condition: Communication Fail From User Interface Control TO Electronic Control Board
Repair or Check: Remove power to the dishwasher and check for any loose wiring connections between the user interface control and the electronic control board. If the wires and connections check out then replace the user interface control. If the problem persists then replace the electronic control board.
Parts Required: User Interface Control – Electronic Control Board

Electrolux Dishwasher Error Code 10
Fault Condition: Electronic Control Board (Relay) Fail
Repair or Check: A relay on the electronic control board possibly failed. Replace the complete electronic control board.
Parts Required: Electronic Control Board

Electrolux Dishwasher Error Code 11
Fault Condition: Drain Valve Fail
Repair or Check: Remove power to the dishwasher and check the wiring for the drain valve. If the wiring checks out then replace the drain valve.
Parts Required: Drain Valve

Electrolux Dishwasher Error Code 12
Fault Condition: Drain Valve Position (Drain valve has activated when it should be turned off)
Repair or Check: Remove power to the dishwasher. Check the drain valve wiring for an issue. If the wiring checks out then replace the electronic control board. (This is because the drain valve relay on the control board is stuck) If the problem persists then replace the drain valve.
Parts Required: Electronic Control Board – Drain Valve

Electrolux Dishwasher Error Code 13
Fault Condition: Electronic Control Board Fail
Repair or Check: The control board has a component failure. Replace the complete electronic control board.
Parts Required: Electronic Control Board

Electrolux Dishwasher Error Code 30
Inconsistency between level on electronic pressure switch and level on anti boiling pressure switch.

Electrolux Dishwasher Error Code 50
Fault on the wash motor circuit. On some Electrolux dishwashers the motor has a control board located at the back at the bottom just behind the wash motor.

To find the model number of your Electrolux Dishwasher, check on the sides of the frame as shown in the image below.

model number location on Electrolux dishwashersModel number location on Electrolux dishwashers

Do you know of other Electrolux Dishwasher error codes? Do you have an error code on your Electrolux dishwasher and need help finding and fixing the problem? Please leave a comment or question below.


52 thoughts on “Electrolux Dishwasher Error Codes – How To Clear – What To Check”

  1. My dishwasher “error” no is d:on I’m not sure what it means but the programme won’t start for me, the code appears for like 5 sec and then disappears, when I select the programme it is not starting but countdowns instead. After countdown the appliance beeps and goes off. Why could it be? It is Electrolux KEQB7300L

  2. ALLEN VETTER - DIY Repair Assistant

    Niall,
    How to reset an Electrolux Dishwasher ESL8330RO:
    1. Turn off the dishwasher from the power supply for at least 3 minutes.
    2. In the control board, capacitors are used, which have a property to keep the charge of electricity for some time.
    3. After a couple of minutes, the energy will dissipate.
    4. Then turn on the appliance, and select the dishwashing program you need.

    -RR

  3. I have an Electrolux Dishwasher ESL8330RO and the cycle time for Program P1 has increased from approx. 3h40 to 5h33 and when I select the Time Manager Button, the cycle times reduces to 3h33 instead of the 1h25.
    Can anyone advise how to remove this cycle time error or know how to restore the dishwasher factory settings

  4. I have Electrolux EI24ID81SS0A. It shows code i50. After I disconnected the power, it can start to work for a while, then stop and i50 again, water in the bottom. Occasionally it can complete the whole circle, but finally show i50.

  5. My new AEG FSB41600Z dishwasher is turning on, then soon beeping 6 times and showing ,11. This number is not in the trouble shooting pages of the manual. Can you help please?

  6. William Michelson

    I have an Elektrolux Dishwasher Model ESL670706. When I press start an alarm 174 keeps appearing and the pump does not sound to start pumping. What is the problem?

  7. My Electrolux dishlex model D/DX403WB/W keeps showing a 60 number and beeping during the wash cycle. The 60 is not mentioned in the fault guide

  8. I have an EIDW6105GS1 that all the lights flashing(no display).
    When powering down and back up I hit normal wash that light lights up but when I hit start they all come back on.
    Please Help!!!

  9. I have the exact same model and issues. Replaced the drain valve, but no success. Did you ever figure this out?

  10. I have an Electrolux dishwasher, model# EIDW5705PSOA. It shows “Er” on the panel but no code number. The 2 small indicator dot lights to the right of the Cancel button are both lit as well as the hi temp button is lit.
    I have turned off power from the breaker for 3 minutes 2 days ago. It seemed to have worked as the lights were not lit any more but we just ran the dishwasher yesterday; the exact same lights are lit again after the load was over (at least I think the wash was completed as we ran it overnight).
    Let me know if you can help. Thanks!

  11. We have an industrial Electrolux 20606042 washer with error code CAII. Please what does this mean and how can we resolve it.

  12. I have a small “bench”-dishwasker, Electrolux ESF2300OS. Now it shows the code “99”, the door will not close and the program will not start… If I hit “reset” the panel looks normal again until I try to start the machine again byt closing the door.

  13. I have error code 99 on my Electrolux dishwasher GA55GLV400. How do I fix that? Thank you!
    Richard

  14. My two year old Electrolux dishwasher is showing a code that I’ve never seen before. What does ,CO mean?

  15. I have an Electrolux integrated dishwasher (ESL6211LO). When it’s turned on the →| indicator flashes as if the cycle has finished. The drain is clear. Would you know what this could mean??

  16. Sebastian Mmole

    I hv electrolux washer model EWF 1234 type P6847448 serial no 43400142 it is working sometime flashes on and off Error code indicates E 90 any suggestions to the problems

  17. Electrolux ESL6370R0 Dishwasher. I don’t have any error codes and the machine functions as it should, escept that it doesn’t heat up. I’ve replaced the heating element and the thermostat with no joy. Are there any other sensors or any other ideas out there…?
    Thanks

  18. I have a EW24ID80QS dishwasher. I purchased new a month ago. It has never dried or heated water. The control panel was replaced that did not help. Technician checked the heater and has the correct resistance but will not draw any amperage the wiring is good as well. Any suggestions?

  19. Electrolux dishwasher E24ID74QPS0A flashes on and off the control touch pads on the left side of the control panel. And it does this intermittently. Seems to be working otherwise.

  20. I have this same problem the owners manual does not address the issue in the book. Any input? All three delay lights and intermittently two beeps on the air dry light.

  21. DIY Project Help Tips

    Rawan,

    Is the Electrolux dishwasher error code you are getting showing E30 or just 30?

    Electrolux dishwasher error code E30 is NOT in the database.
    In the meantime simply attempt to reset your Electrolux dishwasher.
    This can be done by unplugging it.
    -Unplug the dishwasher or flip OFF the breaker.
    -Wait 15 minutes and then apply power back to the dishwasher and turn it ON.
    -Run a test wash to see if the error code is cleared.

    If resetting the dishwasher by disconnecting power does not fix and clear the error code, there could be other issues.

    If you are getting JUST the 30 error code, here is what is going on:
    Electrolux Dishwasher Error Code 30 means you have a leak.
    Water has gone in and down into the base.
    This then triggers the antiflood switch and shows the 30 error code.
    Electrolux Dishwasher 30 error code means the drain pump is running constantly – If so unplug the dishwasher.
    -Tip the dishwasher backwards to get the water out of the base.
    -Once the water is emptied the antiflood switch will deactivate and reset.

    Advise us of any new error code(s) that may display or if it still displays error code E30?
    This information can help us to better research the issue and decide if another route of troubleshooting is needed.

    -RR

  22. I have an Electrolux dishwasher Model Number ESF5511LOX.
    I am getting the Error code E30.
    What can I do?

  23. I have an Electrolux dishwasher Model EDW7505HPS0A. Error code 11… drain valve.
    I replaced the drain valve with a new one, but when testing, the same error code showed up again.
    Usually when starting the dishwasher, you can hear it filling up.
    Now it is silent until 15 seconds pass and the beeping error code 11 starts.
    Any help would be greatly appreciated.

  24. Dishwasher 911D93 no water coming into the machine and continuous beeping any suggestions ?

  25. DIY Project Help Tips

    Kees,
    The Electrolux Dishwasher Error Code 30 means the Anti flood float switch may be the cause of the error.
    Inconsistency between level on electronic pressure switch and level on anti-boiling pressure switch.

    Possible Causes are…
    Pressure switch defective
    Electrical current leak between heating element and ground
    Heating element
    Wiring defective
    Main board defective

    -RR

  26. We have an Electrolux Dishwasher showing error code 30 on the display.
    The motor of the dishwasher keeps on running after turning off.

  27. I have the same problem with me Electrolux Dishwasher it is flashing E60 on display.
    Is it safe to use the machine in this state?
    Electrolux
    ESF65052W.
    Typ 911D12621D or L (blurred)
    PNC 911 543 011 01.
    S-No 94865746.

  28. I have the same problem and I have a Ex302. Did you find out what it was? Just thought I’d try as I can’t get a manual.

  29. I have Electrolux dishwasher model #EIDW6105GS1. The last time I ran the dishwasher, the bottom rotating arm was caught on a dish in the bottom tray. Now all the lights across the top are flashing. When I hold down any button the flashing stops, then when I press the “ready” button, the flashing starts again. I tried turning off the breaker tnen turning it back on. That did not reset it. What else can I do?

  30. I’m having the same problem, I have to shut it off at the breaker, it resets but when I go to start it up it gives the code again. I have cleaned the filter.

  31. My Electrolux dishwasher model # EI241D30QS is flashing the delay button and intermittently flashing and beeping the air dry button.

  32. Electrolux Gallery Dishwasher model – ESI618OU
    Hi, I’ve accidentally pressed hour delay (11) instead of my usual programme 11. When I tried to clear it by pressing the program button for 5 seconds it didn’t reset to the clear dashes, i’ve tried that 3 times then 10 seconds, 20 seconds, turning it off and on again – it’s still flashing H with the steady 11 next to it. Does this mean it’s going to start running in 11 hours from now (will i be able to fix it after?) and/or is there any other way to reset it?

  33. Yes thank you, I’ve looked and could not find anything. I turned off the pose and it reset. Now it’s doing it again. When I turn it off it now will not reset?

  34. My Electrolux dishwasher keeps flashing an arrow symbol when i attempt to use it, what does this mean?

  35. DIY Project Help Tips

    Samantha,
    Electrolux Dishwasher with error code i50 = A problem has been detected with the drain or wash motor.
    Pressing the cancel button or turning power off at the breaker for 5 minutes should clear this error code and the unit can be restarted.
    -RR

  36. Electrolux Dishwasher was working fine, now it is displaying error code i50 and won’t clear or stop beeping. Model EI24ID50QS0B. What can i do to fix this?

  37. DIY Project Help Tips

    Jill Duffy,
    Check the bottom of your Electrolux dishwasher to be sure there is no blockage near the sump.
    There may be food particles or broken glass that is blocking the dishwasher and making it unable to properly drain.
    -RR

  38. I have an Electrolux dishwasher, model number E1241D50QS0B. It’s been acting up by not washing through a whole cycle but now it just won’t stop draining with nothing to drain. It has a half a one and 30 after it on the digital pad. Please help I’m afraid it’ll burn out.

  39. DIY Project Help Tips

    John,
    Can you give us the model number of your Electrolux Dishwasher?
    At which cycle does the noise and flashing “60” appear?
    The model number will be located on the inside door or door frame area on the dishwasher.
    -RR

  40. My Electrolux Dishwasher is stopping a few minutes into the cycle and making a noise and flashing 60.

Leave a Comment

Your email address will not be published.

This site uses Akismet to reduce spam. Learn how your comment data is processed.