Samsung Dishwasher Flashing LC Code – WATER LEAK ERROR

Dishwasher shows LC code and needs to be reset. My Samsung dishwasher is flashing the error code LC. During a wash load of dishes the dishwasher stopped and began flashing LC. Now the dishwasher is not usable. I have tried to reset the dishwasher by pressing the buttons on the control panel but it has not cleared the code. I do not see any water leak under the dishwasher. I would like to know what this code means and how do I fix and clear the code? The dishwasher is 8 months old and is model number DW7000.

How To Fix Samsung Dishwasher LC Code

Quick answer: The LC flashing on your Samsung dishwasher indicates that the leak sensor in the dishwasher detects a water leak or moisture. To clear the error code LC, simply remove power to the dishwasher for 15 minutes. This should reset the Samsung dishwasher and clear the error code. If the error code does not clear, there may be a LEAK SENSOR FAULT or the dishwasher has an actual WATER LEAK.

NOTE: When the dishwasher bottom pan is damp or has moisture (does NOT have a true water leak) the dishwasher thinks there is a water leak thus causing multiple issues concerning the code LC or LE.

Samsung Dishwasher Code LC or LE = Water Leakage Error

The dishwasher sensor has detected a water leak or moisture. (On Waterwall model dishwashers: The water reflector is blocked)

Samsung Dishwasher LC LE Code

First, find out if your Samsung dishwasher is actually leaking water. Check under the dishwasher. If water is present, then the dishwasher is most likely leaking water and the code LC or LE is correctly displayed.

Is your dishwasher actually leaking water? If yes, click the link to fix the water leak… How to fix a dishwasher that leaks water

If your dishwasher does not have a water leak, here are other issues that can cause the LC or LE error code…

Dishwasher detergent overfill?

Do not overfill the dishwasher with detergent. If the dishwasher dispenser is overfilled with detergent or has excess detergent, the LC code can occur.

Dishwasher was recently moved or installed?

The dishwasher may have some moisture or water that has gotten on the sensor, give the sensor time to dry to clear the LC code.

Dishwasher recently connected to garbage disposal?

A newly installed garbage disposal that is attached to the dishwasher may be the cause of the problem if the cap on the garbage disposal is not removed. Inspect to be sure the cap is removed to clear the LC code.

Dishwasher keeps flashing LC code?

If the code continues to flash on the display, to clear the error code, remove power by unplugging the dishwasher for 15 minutes. This is to reset the dishwasher and also allow the water or leak sensor to dry out and stop signalling the code. The leak sensor can sometimes get a small amount of moisture on it. When this happens the sensor senses water and displays the error code on the display. (Once the code is displayed, the pump will drain out any existing water but not continue to advance forward.) If removing power to the dishwasher does not clear the error code, you can call for service or follow the information below…

Unplugging the dishwasher and waiting 15 min did not reset the code… If the above solutions do not clear the LC or LE code on your Samsung dishwasher, you can try to adjust the leak sensor within the dishwasher.

Samsung Dishwasher Leak Sensor Assembly

How To Fix Samsung Dishwasher with LC Error Code

How to fix a Samsung dishwasher with the LC/LE error code… (Water Leak OR Leak Sensor Issue)

1. Unplug the dishwasher from power.
2. Remove screws holding dishwasher to cabinet.
3. Slide the dishwasher out of cabinet to gain access.
4. Remove the bottom square panel tray. (Location depends on model number)
5. Dry any moisture or water in the dishwasher.
6. Locate the leak sensor. (Located on drain pan on bottom of unit)
7. Relocate the leak sensor up a few inches higher.
8. Check ALL water lines to be sure they are secure and not leaking.
9. Install the bottom square panel.
10. Slide the dishwasher back into place.
11. Install screws to secure dishwasher.
12. Plug dishwasher into power.
13. Test dishwasher to check that the error code LC or LE is fixed/cleared.

Still need help? If you are still having a problem, you can contact Samsung service here – Samsung Dishwasher Support

If your Samsung dishwasher has the LC or LE code and the above information did not fix your problem, please leave a detailed question about your issue. Please tell us the model number of your dishwasher (ex. DW80K5050US, DW7000KM) and we will complete the troubleshooting to fix your dishwasher.

Written by Keith Schneerer

Certified Appliance Tech · Founder, RemoveAndReplace.com

Keith has spent 30+ years repairing machines, starting as a military mechanic and later maintaining food processing equipment before moving into appliance repair. He founded RemoveAndReplace.com to share field-tested repair advice.

More about Keith →