Frigidaire dishwasher has an error code? Frigidaire dishwashers have built in diagnostic systems. If your dishwasher finds, sees, or detects a fault or error in the system, it will show an error or fault code. The error code will display where the usual numbers are on the display screen. When an error code is displayed, your dishwasher is telling you a specific fault. The error code will tell you which parts on your Frigidaire dishwasher to replace or check. You can also Search YouTube for Frigidaire Dishwasher Error Codes or get advice from your Frigidaire dishwasher owners manual when your Frigidaire Dishwasher Is Displaying An Error Code. NOTE: Before ordering any parts from the ones listed below, check that the parts will fit with your model number Frigidaire dishwasher.
Frigidaire Dishwasher Error Codes
Frigidaire Dishwasher Error Code = i10
Error Problem / Condition = A low fill has been detected.
Check / Repair / Solution = Look for a pinched water supply line, or water shutoff is not completely opened.
Frigidaire Dishwasher Error Code = i20, i40, iF0
Error Problem / Condition = Clogged filters or a restricted drain line has been detected.
Check / Repair / Solution = Check and clean both filters and sump area and check for a pinched or blocked drain hose. If the drain line is attached to a disposer, check that the knockout plug has been removed.
Frigidaire Dishwasher Error Code = i30
Error Problem / Condition = A leak or over flow of water has been detected in the bottom pan.
Check / Repair / Solution = Look for loose connections at the water inlet valve and ensure the unit is properly leveled.
Frigidaire Dishwasher Error Code = i50
Error Problem / Condition = A problem has been detected with the drain or wash motor.
Check / Repair / Solution = Pressing the cancel button or turning power off at the breaker for 5 minutes should clear this error code and the unit can be restarted.
Frigidaire Dishwasher Error Code = i60
Error Problem / Condition = A problem has been detected with the water heating system.
Check / Repair / Solution = Pressing the cancel button or turning power off at the breaker for 5 minutes should clear this error code and the unit can be restarted.
Frigidaire Dishwasher Error Code = iC0
Error Problem / Condition = A problem has been detected with the electronic control system.
Check / Repair / Solution = Pressing the cancel button or turning power off at the breaker for 5 minutes should clear this error code and the unit can be restarted.
Frigidaire Dishwasher Error Code = UO
Error Problem / Condition = Vent open
Check / Repair / Solution = While in wash cycle, Main Control Board does not receive signal from vent assembly that vent plunger is closed. Plunger status is sensed with optical sensor in vent assembly. Check wiring between vent assembly and Main Control Board. If wiring correct, replace vent assembly. If error still exist, replace Main Control Board.
Frigidaire Dishwasher Error Code = UF
Error Problem / Condition = Fan not running
Check / Repair / Solution = While in drying cycle, Main Control Board not sensing vent fan motor rotation at correct speed. Check wiring between vent assembly and Main Control Board. If correct, replace vent assembly. If error still exist replace Main Control Board.
Frigidaire Dishwasher Error Code = ER
Error Problem / Condition = Membrane Switch Failure
Check / Repair / Solution = Main Control Board has detected a stuck key or a key pressed for more than one minute. Check connection from keypad to Main Control Board. If correct, replace keypad. If error still exist, replace Main Control Board.
Frigidaire Dishwasher Error Code = CE
Error Problem / Condition = Configuration Error
Check / Repair / Solution = Check wiring connections between keypad and Main Control Board. Check for correct parts installed. Replace parts accordingly.
Frigidaire Dishwasher Error Code = CL
Error Problem / Condition = Close Door – Door Switch Open
Check / Repair / Solution = Main Control Board not sensing door closed. Close door. Check door switches. Check wiring between door switches and Main Control Board. If wiring and switches are correct, replace Main Control Board.
Frigidaire Dishwasher Error Code = dP
Error Problem / Condition = Drain Pump
Check / Repair / Solution = Displayed in relay test when drain pump is activated.
Frigidaire Dishwasher Error Code = FL
Error Problem / Condition = Water Valve Is Open
Check / Repair / Solution = Displayed in relay test when water valve is activated.
Frigidaire Dishwasher Error Code = HO
Error Problem / Condition = Heat Delay
Check / Repair / Solution = The control is delaying cycle to allow water temperature to rise to correct temperature in attempt to assure optimum performance.
Frigidaire Dishwasher Error Code = hs
Error Problem / Condition = Hall Sensor
Check / Repair / Solution = The control has sensed an error with hall sensor in motor. Check wiring between motor and Main Control Board. If correct, replace motor. If error still exist, replace Main Control Board.
Frigidaire Dishwasher Error Code = LO
Error Problem / Condition = Low Rinse Aid
Check / Repair / Solution = Rinse aid level is low. Refill rinse aid dispenser.
Frigidaire Dishwasher Error Code = PF
Error Problem / Condition = Power Failure
Check / Repair / Solution = A power failure has occurred. More than 10% of power has dropped to the unit. Check house wiring.
Frigidaire Dishwasher Error Code = rA
Error Problem / Condition = Rinse Aid
Check / Repair / Solution = The control has sensed a problem with the reed switch in the dispenser. Refill the rinse aid dispenser. If error still exist, check wiring between dispenser and Main Control Board. If not corrected, replace dispenser assembly. If error still exist, replace Main Control Board.
Frigidaire Dishwasher Error Code = RE
Error Problem / Condition = Rinse aid reed switch
Check / Repair / Solution = Rinse aid reed switch in dispenser is closed.
Frigidaire Dishwasher Error Code = RF
Error Problem / Condition = Rinse aid
Check / Repair / Solution = Rinse aid reed switch in dispenser is open. Refill rinse aid dispenser. Replace dispenser assembly.
Frigidaire Dishwasher Error Code = rt
Error Problem / Condition = Relay / Triac Test
Check / Repair / Solution = Relay test mode has been activated.
Frigidaire Dishwasher Error Code = Sd
Error Problem / Condition = Detergent Dispenser
Check / Repair / Solution = Displayed in relay test mode when detergent dispenser is activated.
Frigidaire Dishwasher Error Code = tu
Error Problem / Condition = Turbidity Sensor
Check / Repair / Solution = The Main Control Board has sensed a failure in the turbidity sensor. Check wiring. If wiring correct, replace turbidity sensor. If error still exist replace Main Control Board.
Frigidaire dishwasher error codes list
Frigidaire dishwasher internal parts identification
Water Test Mode
To activate water test mode on your Frigidaire dishwasher, press and hold Start/Cancel and heating option (High-Temp Wash, Sanitize, Air Dry, or No Heat Dry) (depending on model) for 3 seconds. To advance through test(s), press Start/Cancel. If component tested fails, error code will be displayed in digital display.
Frigidaire dishwasher test mode chart
Frigidaire dishwasher parts
Do you know of other Frigidaire Dishwasher error codes? Do you have an error code on your Frigidaire dishwasher and need help finding and fixing the problem? Please leave a comment or question below.
Written by Keith Schneerer
Certified Appliance Tech · Founder, RemoveAndReplace.com
Keith has spent 30+ years repairing machines, starting as a military mechanic and later maintaining food processing equipment before moving into appliance repair. He founded RemoveAndReplace.com to share field-tested repair advice.
More about Keith →
Fridgidare keeps repeating wash cycle and doesn’t stop
Geoff,
So after accidentally adding hand soap to your dishwasher, the pump constantly runs?
Does the pump run when you open the dishwasher door still?
You may want to flip the breaker to it for 30 to 60 minutes to see if that resets the i30 error code, the longer is better in some cases.
The excess soap may have gotten certain parts “wet”, so it may help to give it time to let it “dry” out.
-RR
I accidentally put hand wash soap into my dishwasher tonight.
It overflowed bubbles through the door and was full of bubbles.
Now it runs continuously (for hours) and when I open the door it still runs and displays an i30 code.
The drain seems clear and I have dumped several cups of water through the drain and the machine continues to pump until it’s empty, but won’t stop after that.
I have attempted to reset the code by holding startand water temp for 3 seconds or more, to no avail.
I have reset the breaker several times to no avail.
I have the same problem and we had a serviceman repair 2 weeks ago and replaced the motor which worked for 2 weeks but now it is doing same thing and had to shut breaker again so I will be calling them back tomorrow.
Frigidair galleria dishwasher Blinks PF (power failure) code, won’t clear
Screen was all black and unresponsive, manually reset breaker at box. DW began blinking PF code.
*Attempted to clear with “Start/cancel” button but entire panel is unresponsive.
*Attempted multiple hard resets via breaker panel, continues to flash Pf error code.
*Attempted closing and reopening door, this stops the PF from flashing but panel goes black and unresponsive.
*Attempted diagnostics test by holding start and wash temp, unresponsive
Thanks in advance!
Did you figure it out? I’ve got the exact issue…
my Frigidaire Professional Series dishwasher keeps having a PF code. it’s been doing it for 2 or 3 months but it normally does it without draining all the water out