Kenmore dryer error codes are shown on the dryers display to help you to troubleshoot the problem with your dryer. The error codes below will help you to identify what is wrong with your Kenmore Elite dryer. Once you have identified the error code, this code will tell you which part is causing the error code. You can then check the part and repair or replace that part when needed. Kenmore dryer help videos are here. Kenmore Elite dryer manuals are here.
Kenmore Elite Dryer Error Codes
Kenmore Elite Dryer Error Code = PF
Error Condition = Power Failure
Check or Repair Needed = Power failure while the dryer was in cycle. Press the Stop button to clear the display. If you experience common power failures on your dryer be sure to check the electrical outlet cord.
Replacement Parts = Outlet Cord
Kenmore Elite Dryer Error Code = F01
Error Condition = Main Electronic Control Board Fail
Check or Repair Needed = Remove the dryer from power for 10 minutes. Apply power back to the dryer and if the code returns you need to replace the main electronic control board.
Replacement Parts = Main Electronic Control Board
Kenmore Elite Dryer Error Code = F02
Error Condition = Keypad or User Interface Fail
Check or Repair Needed = A button on the keypad may be stuck on one of the user interface controls. If the button cannot be unstuck then replace the user interface control assembly.
Replacement Parts = User Interface Control Assembly
Kenmore Elite Dryer Error Code = F20
Error Condition = Heater Relay Fail
Check or Repair Needed = The heater relay on the main electronic control board has failed. Remove power to the dryer and replace the main electronic control board.
Replacement Parts = Main Electronic Control Board
Kenmore Elite Dryer Error Code = F22
Error Condition = Outlet Thermistor (Temp Sensor) Fail
Check or Repair Needed = The controller indicates an electrically open outlet temperature sensor (thermistor). Remove power from the dryer. Use a multi-meter and check the resistance of that particular thermistor/temp sensor (10,000 ohms). If the outlet temperature sensor is bad then replace it.
Replacement Parts = Outlet Thermistor (Temp Sensor)
Kenmore Elite Dryer Error Code = F23
Error Condition = Outlet Thermistor (Temp Sensor) Fail
Check or Repair Needed = The controller indicates an electrically open outlet temperature sensor (thermistor). Remove power from the dryer. Use a multi-meter and check the resistance of that particular thermistor/temp sensor (10,000 ohms). If the outlet temperature sensor is bad then replace it.
Replacement Parts = Outlet Thermistor (Temp Sensor)
Kenmore Elite Dryer Error Code = F24
Error Condition = Inlet Thermistor (Temp Sensor) Fail
Check or Repair Needed = The controller indicates an electrically open inlet temperature sensor (thermistor). Remove power from the dryer. Use a multi-meter and check the resistance of that particular thermistor/temp sensor (50,000 ohms). If the inlet temperature sensor is bad then replace it.
NOTE: The inlet thermistor is part of the high limit thermostat on this dryer.
Replacement Parts = High Limit Thermostat – Inlet Thermistor (Temp Sensor)
Kenmore Elite Dryer Error Code = F25
Error Condition = Inlet Thermistor (Temp Sensor) Fail
Check or Repair Needed = The controller indicates an electrical shorted inlet temperature sensor (thermistor). Remove power from the dryer. Use a multi-meter and check the resistance of that particular thermistor/temp sensor (50,000 ohms). If the inlet temperature sensor is bad then replace it.
NOTE: The inlet thermistor is part of the high limit thermostat on this dryer.
Replacement Parts = High Limit Thermostat – Inlet Thermistor (Temp Sensor)
Kenmore Elite Dryer Error Code = F28
Error Condition = Moisture Sensor Fail
Check or Repair Needed = Remove power from the dryer. Check the wiring harness on the moisture sensor visually and with a multi-meter. If the wiring connections are okay then replace the moisture sensor.
Replacement Parts = Moisture Sensor
Kenmore Elite Dryer Error Code = F29
Error Condition = Moisture Sensor Fail
Check or Repair Needed = Remove power from the dryer. Check the wiring harness on the moisture sensor visually and with a multi-meter. If the wiring connections are okay then replace the moisture sensor.
Replacement Parts = Moisture Sensor
Kenmore Elite Dryer Error Code = F30
Error Condition = Restricted Outlet Airflow
Check or Repair Needed = Check the lint screen filter and clean of any lint. Remove fabric softener buildup on the lint screen if necessary. Clear lint blockage restriction from the air vent exhaust system.
Kenmore Elite Dryer Error Code = F31
Error Condition = Low L2 Voltage
Check or Repair Needed = The L2 leg of the 240 volt power is below 30 volts. Check circuit breakers for the dryer and reset the L2 breaker if needed. Remove power to the dryer then check the power cord wire connections on the terminal. If any loose wires are found resecure them. Replace the power cord if it has become damaged. Check the 240 volt power supply to the dryer.
Replacement Parts = Electrical Power Cord
Kenmore Elite Dryer Error Code = F70 F71
Error Condition = No communication between the ECB (electronic control board) and the UICB (user interface control board assembly)
Check or Repair Needed = Remove power from the dryer. Check the wire harnesses visually and with a multi-meter from the electronic control board and the user interface control board. If the connections are okay then the main electronic control board and the user interface control assemblies may need to be replaced.
Replacement Parts = Main Electronic Control Board – User Interface Control
Kenmore Elite Dryer Error Code = F72 – F78
Error Condition = User Interface Control Assembly Fail
Check or Repair Needed = Remove power from the dryer. Check the wire harness connections between the user interface assemblies visually and with a multi-meter. Check the wire harness connections between the main electronic control board and the user interface assemblies visually and with a multi-meter. If the wiring connections are okay then one or both of the user interface control assemblies may need to be replaced.
Replacement Parts = User Interface Control Assembly
Kenmore Elite Dryer Parts
More clothes dryer troubleshooting for Frigidaire Dryer Error Codes, GE Dryer Error Codes, Kenmore Dryer Error Codes, LG Dryer Error Codes, Maytag Dryer Error Codes, Samsung Dryer Error Codes, and Whirlpool Dryer Error Codes.
If your Kenmore Elite Dryer error code is not listed here or you have issues with any Kenmore Elite Dryer Error Code, please leave a comment below and we will be happy to assist you with your dryer error code problem. If you have any other misc questions about your Kenmore Dryer, you can ask questions about that specific model dryer and we can further assist.
Written by Keith Schneerer
Certified Appliance Tech · Founder, RemoveAndReplace.com
Keith has spent 30+ years repairing machines, starting as a military mechanic and later maintaining food processing equipment before moving into appliance repair. He founded RemoveAndReplace.com to share field-tested repair advice.
More about Keith →
My Kenmore Elete will not stop running unless I open the door or thow the breaker
Error codes u19. , D04 518 , 18:88
Can you help me find out what id wrong with it
I had a F25 and F28 code on my dryer. I ordered the parts for the faults and removed and replaced them. Then cleaned the whole unit including the duct routed though the house. The unit works fine , all test work as instructed by manual. The problem is I cant get the codes to erase or reset. I figure if the parts and circuit including testing properly,that the codes would be removed by themselves. Is there a series of buttons to press to reset like there is to find faults?
kenmore elite with error codes SRU and CLL model 4178110 Where do i fine the meaning of these codes?
Error code is dr on my kenmore elite front load dryer.
I have the Kenmore Elite Model 417.18100000 dryer that has the “cll srv” code. How do I put this unit in diagnostic test mode
Bought a new washer and dryer , on 06/06/2017 the day sears delivered it my wife washed a batch of towels and tryed using the dryer and it would stay on for 10 minutes and turn off with a error code np??
They are Kenmore elite set.
When the delivery guys installed the units they tryed three diffrent power cords? Its a electric dryer.
I have a problem with my Kenmore Elite He5 gas dryer. It was operating in the Wrinkle Guard mode but quit displaying a PF70 code. It would not turn on, off, or do anything ecxept display the PF70. I unplugged it and allowed it to sit for awhile before plugging it back in. Now it will not turn on at all only beeping when you attempt to do so.