Home » Home DIY Repair » Washing Machine Repair » Blomberg Washing Machine Error Codes

Blomberg Washing Machine Error Codes

Blomberg washer showing error code? When your Blomberg washing machine shows an error code, it is identifying a problem. The code that shows on the washing machine’s display is informing you a specific part or component in the washer needs to be checked, cleaned, or replaced. The error codes below for Blomberg washing machines will tell you exactly what the issue is with your washer.

You can then troubleshoot the problem and by understanding what the error code means, you can replace parts yourself and save money. Below the error codes are troubleshooting methods for common Blomberg washer problems. NOTE: Always remember to unplug the washing machine from power when troubleshooting, disassembling, and replacing parts.

Blomberg Washing Machine Error CodesBlomberg Washing Machine Error Codes – How To Clear/Reset?

The most common errors on Blomberg Washing Machines is DOOR LOCKED, DOOR ERROR, and NOT SPINNING. If your washer is front loading and has a display screen, an error code will show for these common issues. Use the error codes below to identify and repair your washer. The video below will assist you in keeping your Blomberg washer running smooth. Watch the video for ways to reset some error codes.


Blomberg Washing Machine Maintenance Help

Blomberg Washing Machine Error Code 01

Blomberg Washer Error Definition = There is a problem with the water inlet valve
The Error Code Shows Because: The washing machine does not fill with water
What To Check/Clean/Repair/Replace?
-Be sure the water supply to the washer is on and flowing
-Be sure the water supply hoses are not bent
-Inspect the inlet valve mesh filters for clogs/blockage
-Inspect the water inlet valve for mechanical or electrical failure

Blomberg Washing Machine Error Code 02

Blomberg Washer Error Definition = A draining fault has been found
The Error Code Shows Because: The washer will not drain water out
What To Check/Clean/Repair/Replace?
-Inspect the drain pump filter for blockage
-Inspect the drain pump for blockages
-Inspect the outlet hose for blockage
-Inspect the drain pump to be sure it is operational
-Inspect the drain pump wire harness to be sure it is secure

Blomberg Washing Machine Error Code 03

Blomberg Washer Error Definition = A heating fault has been found
The Error Code Shows Because: The washer is unable to heat water
What To Check/Clean/Repair/Replace?
-Inspect the wires from heater element and thermostats
-Inspect the heating element
-Inspect the thermostats

Blomberg Washing Machine Error Code 04

Blomberg Washer Error Definition = The motor triac has shorted
What To Check/Clean/Repair/Replace?
-Inspect the motor connect block
-Inspect the wiring harnesses
-Inspect the electronic control board

Blomberg Washing Machine Error Code 05

Blomberg Washer Error Definition = Washer has detected a temperature NTC fault
What To Check/Clean/Repair/Replace?
-Inspect the temp sensor wires
-Inspect the temp sensor

Blomberg Washing Machine Error Code 06

Blomberg Washer Error Definition = Washer has found a motor tacho fault
What To Check/Clean/Repair/Replace?
-Inspect the motor connect block
-Inspect the wiring
-Inspect the carbon brushes on the motor
-Inspect the tacho connections
-Inspect the motor

Blomberg Washing Machine Error Code 07

Blomberg Washer Error Definition = Door lock error – Door latch error
The Error Code Shows Because: The washer door is not detected as closed
What To Check/Clean/Repair/Replace?
-Inspect that the door is fully closed
-Inspect the door latch
-Inspect the door catch
-Inspect the door lock wires
-Inspect the door lock

Blomberg Washing Machine Error Code 09

Blomberg Washer Error Definition = Program select fault error
What To Check/Clean/Repair/Replace?
-Inspect the program selection connection
-Inspect the wiring
-Inspect the electronic control board

Blomberg Washing Machine Error Code 10

Blomberg Washer Error Definition = A water overfill overflow has been detected
The Error Code Shows Because: The washing machine overflows with water
What To Check/Clean/Repair/Replace?
-Inspect the level sensor connector block
-Inspect the wiring
-Inspect the electronic control

Blomberg Washing Machine Error Code 11

Blomberg Washer Error Definition = A water heat fault has been detected
The Error Code Shows Because: The washer will not heat water
What To Check/Clean/Repair/Replace?
-Inspect the wires to heat element and thermostats
-Inspect the thermostats
-Inspect the wash heater

Blomberg Washing Machine Error Code 12

Blomberg Washer Error Definition = A door latching error has been detected – Door error
What To Check/Clean/Repair/Replace?
-Be sure the door is fully closed
-Inspect the door lock connect block
-Inspect the wires

Blomberg Washing Machine Error Code 13

Blomberg Washer Error Definition = A spin speed fault has been detected
What To Check/Clean/Repair/Replace?
-Inspect the washer belt
-Inspect the motor connect block
-Inspect the wires / wiring harnesses
-Inspect the carbon brushes in motor
-Inspect the tacho connection
-Inspect the motor

Blomberg Washing Machine Error Code 18

Blomberg Washer Error Definition = Voltage power infrequency fault
The Error Code Shows Because: The washer is not receiving the correct voltage/power
What To Check/Clean/Repair/Replace?
-Be sure the washer is getting the correct voltage
-Check breaker or fuse
-Check with meter

IMPORTANT NOTE: The error codes above are used on German built Blomberg washers. At one time the company was owned by Brandt. The Brandt company was reorganized and Blomberg was sold to Beko. These error codes do not apply to washing machines built by Beko with the Blomberg name badge on them.

Blomberg washing machine control panel function identificationBlomberg WM 26110 NBL00 washing machine control panel function

 

Blomberg washing machine basic parts identificationBlomberg washing machine basic parts identification

Washing Machine Spare PartsWashing Machine Spare Parts

Need help troubleshooting your Blomberg Washer? Here is the washing machine service manual for the Blomberg Washer Manual Model Number WM 26110 NBL00 and the Blomberg Washer Manual WM 67120 NBL00(Owner’s Guide & Installation Instructions)

Below are troubleshooting methods for Blomberg Washing Machines…

blomberg-washing-machine-troubleshooting-1 blomberg-washing-machine-troubleshooting-2 blomberg-washing-machine-troubleshooting-3 blomberg-washing-machine-troubleshooting-4 blomberg-washing-machine-troubleshooting-5 blomberg-washing-machine-troubleshooting-6 blomberg-washing-machine-troubleshooting-7 blomberg-washing-machine-troubleshooting-8 blomberg-washing-machine-troubleshooting-9Blomberg washing machine troubleshooting guide

If you need help with your Blomberg washer, call the toll free number 1-800-459-9848 for assistance for an authorized Blomberg service agent.

 

Blomberg Washing MachinesBlomberg Washing Machines
Model Numbers = WM77110 – WM77120 – WM87120 – WM98400 – WM98200

If you have questions about Blomberg washer error codes or troubleshooting your washing machine, please leave your comment below and we will have an appliance technician answer your question.

Leave a Reply

10 thoughts on “Blomberg Washing Machine Error Codes”

  1. Model no LWF3114420W had this machine for 2 weeks, it is now showing Test on the display, can you help us on how to get rid of it please

  2. my blomberg washing machine wnf8402 rce20 is making problem when i press power on button so door lock is locked immediately pleas help me.

  3. My washing machine as stooped half way though cycle and is showing LL but the second L is the opposite way round i can’t find the manual for it and wondering if you could help thanks Charlotte

  4. The blomberg washer will not start. It says end right after we push the start button. There is a picture of the wash cycle and it says 1000 in upper left hand side of screen. Help.

  5. Hi my blomberg washine machine is brand new since i have not been able to use it since i bought it. It keeps displaying an HV error. The voltage at home was high but i bought a voltage regulator that stabilized the voltage at 222v, still the washing machine displays this HV error. what can i do to fix this problem?

  6. This means “child-proof lock” is on.
    To switch it off, refer to your manual.
    At my machine it is pressing the 2. and 4. button until “C Off” is displayed.

  7. Karen Godfrey

    I bought my blomberg washing machine in may 2013, its had one repair under its 3 year guarantee already and its gone wrong again! it has an e11 fault. having paid nearly £350 for it because it was a “good reliable machine” I am not happy at being told its just luck and I have a bad machine. and I can pay £173.88 for a repair and as many call out as I like over a year! one would think that if it had been repaired properly you wouldn’t have to call them out again the following month! this is my first posting on this site do I buy a new machine or get this on repaired?

  8. Blomberg Washing machine, when i put what program i want and press start, it shows me C on panel. What is this?

  9. DIY Project Help Tips

    Carol,
    Unplug the washing machine.
    Clean the drain pump filter.
    Plug washer back in and that MAY clear the error code “C ON” on your Blomberg Washer.
    If you still get the error code, let us know.
    You can also call Blomberg and get more information at 1 800 459 9848.
    -RR

  10. My Blomberg front loading washer model 77120 nbl01 machine will not start.
    It displays error code C ON.

Leave a Comment

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.