How to repair an LCD flat screen TV that won’t turn on? I have a 55″ inch flat screen TV that is not working properly and would like to repair it. The TV works but I think maybe a board or a cap inside is bad. Can you give me some advice as to what may be the issue? I will explain what I have found so far. TV has power and it stays on standby just fine, the red light turns on when plugged in but no turned ON. Once turned ON, the light turns orange for a few seconds and then it goes to the ON green light. Sometimes it starts going only to orange but then back to the standby red light. The TV will work but only after turning it ON and OFF like 15 to 40 times. Do you think the power board or power supply is going bad therefore the TV will not turn on properly? Any help is appreciated.
How To Repair An LCD Flat Screen TV With Power Issues
We have seen many large flat screen TVs do this. It is usually one or more bad capacitors on the power board.
- A cap is a few bucks and easy to replace if you can desolder and solder.
- You need to identify the bad capacitor.
- The bad cap will look buldged out or extra fat and deformed.
- The small cross on the top of the cap usually splits when they go bad.
- (This is because of a chemical reaction in the capacitor that expands therefore leading to the buldging.)
- Find the bad cap and replace it.
UNPLUG THE TV FIRST… Then open the TV case carefully and gently. Gain access to the inside of the TV so you can see all the boards inside. Look at the capacitors on the power board for any signs of buldging. If you see no buldging caps then you may need to just replace the complete power board which are not expensive.
LCD LED TV Repair power boards
At times, caps don’t always bulge out & you cannot measure capacitance with a regular volt meter. You COULD order all the electrolytic capacitors you need for the TV power board. This would be time consuming and might not even work. A new power board would make the most sense. Need to find a special part for your LCD or LED flat screen TV? Here is a Parts Store for LCD TV Parts.
TV Power Supply: The power board converts the ac line voltage which is 110 volts AC to lower voltages that are required for the operation of the television, very important is the stand by 5 volts needed by the microprocessor to stay wake so when it receives a command such as power on to turn on the power supply, then the power supply generates the secondary voltages needed which can vary by television, some are 12 to 18 volts needed by the audio circuit and 24 volts supply to the inverter board and numerous other voltages.
LCD LED FLAT SCREEN TV power boards
Here are some videos for Repairing an LCD LED flat screen TV with power issues…
LCD TV Repair – No Power, Power Supply Common Symptoms & Solutions
How to Replace Power Supply
LCD TV Power Supply Tutorial Help for LCD TV Repair Fix
Element Hisense Dynex Insignia LCD TV Power Supply Repair Fix
Involves troubleshooting and repair of the power supply board
Testing LCD TV Power Supply Boards~STEP BY STEP
Need to know for sure if your power supply board is faulty before buying a replacement?
Easy way How to test Capacitors, Diodes, Rectifiers on Powersupply using Multimeter
Best Easy Way How to Accurately test Diodes, Capacitors, bridge rectifiers in TV power supply boards,
“how to use multimeter” to test or read TV parts in power circuit boards commonly in LCD, Plasma, DLP TVs
How to Troubleshoot an LCD TV
Three main ways to troubleshoot an LCD TV that does not require in depth knowledge of TV repair
Do you know of easier ways to diagnose and fix an LCD LED TV with power issues? Please leave a comment below.
My TV POPPED and went blank, and then wouldn’t turn back on. Everything I read online suggested the power board. I just changed it and it still won’t turn on. No red light, no nothing. Any ideas?
Makelesi Adireki,
Sounds like a power board issue.
You may want to take the TV apart safely and check the power supply board.
Might be a bad cap or something else is fried.
-RR
I have a 60 inch LCD flat screen tv. When the power is on, the light turns green for a second, make a clicking sound and then turns back to red. I am not sure as to what could be the problem and how to diagnose the problem.
Christopher Lee Winget,
From what you have described about your Emerson TV, we would guess the power board has failed. Do some further troubleshooting to be sure, but from the description of your problem, it sounds like a bad power circuit board.
-RR
I have an Emerson flat screen it is 55 inches model number is lc501em3 the serial number is DS1A1232115092. My red sleep light does not turn on. Power button does not turn on the TV. When you plug the TV in it makes the sound of powering up if there is no power to the buttons and no power to the screen. The fuses not blown and none of the capacitors appear to be blown either. I do not know what is wrong with it. Any feedback you can give me would be greatly appreciated.
I have a Vizio E422AR… i already replaced the power supply to the tv which i thought was the problem but the TV will come on but not stay on… any ideas?… I’ve already made sure everything was plugged in correctly and the power cord was plugged into a working outlet…
I have an rca 55ls55rs lcd tv. The TV powers on but flickers. I got it from a company that left it on alot. I believe it’s the power supply board but can not seem to locate one. The board says rsag7.820.1357 roh ver.d
Yes I just took it apart today and there is four that is bulged. Well here’s the thing I was driven down the road and there was this TV and a projection TV with a sign that said big one works little one don’t when I got then home it was the opposite and the it worked fine for like a day and half then the Vizio light would stay on orange and click on and of the then it just completely went off no light or anything.
Beau,
You can try replacing the cap… but is the cap visually bulged or look deformed in any way? Try that first and if that does not fix your issue then buying a new power board or main board may be the next step. What exactly is the issue with the TV?
-RR
I have a vp322hdtv10a and I have changed the power cord and it is plugged straight in to the wall. I don’t want to pay 60 for a new power board. Which I’m sure that it has something to deal with and not the main board. Sould I replace the cap first just in case sense it is only $8?