Samsung dryer error codes display on your dryer’s control panel to help you troubleshoot the problem. The error codes below will help you to identify what is wrong with your Samsung dryer. Once you have identified the error code, this will tell you which part is causing the issue. You can then check the part in question and clean or replace it if needed. Samsung dryer help videos are here if needed.
Samsung Dryer Error Codes
Samsung Dryer Error Codes
Related to Heating, Voltage, Temperature, Door, Communication, and Jammed Buttons.
Samsung Dryer Heating Errors = HC4, 1 HC, HC, hE
This means that the dryer is getting too hot (overheat).
Samsung Dryer Communication Errors = AE4, AE3, AE5, E3, 1 AC, AC, Et, AE, EEE
This code means the dryer’s internal components are unable to “talk” to each other. Turn off the dryer for 1 minute and turn it back on again.
Samsung Dryer Frequency Errors = 1 FC, FC, FE
These codes mean that there is an power source frequency issue. Restart the cycle to fix this issue.
Samsung Dryer Voltage Errors = 2E, 9E1, 9C1, 9E
This code appears when the voltage is abnormal being supplied to the dryer.
Samsung Dryer Jammed Button Errors = bC2, 6E, 6E2, 6C2, bE, bE2
This code appears if a button on the dryer panel is found to be as stuck or pressed continuously.
Samsung Dryer Door-Related Errors = dF, do, d0, 1 DC, 1 dF, dC, dE
These codes are related to the door, latch, and sensors. These components detect if secured properly. When the door will not stay closed, or won’t close or latch these codes can show.
Samsung Dryer Temperature Errors = tCS, 1 tC, 1tC5, 1tCS, tS, t5, tC, tO, t0, tE, tE3, tC5
The temperature or the sensors have an issue or fault.
Samsung Dryer Vent Blockage Test Results = C80, C8o, C8, C90, C9o, Ct, Clg, Cl9, Cg, C9
The error codes only show after a Vent Blockage test has been ran.
Specific Samsung Dryer Error Codes
Exact error codes to clear or fix your dryer.
Samsung Dryer Error Code = TE
Error Condition = Defective thermistor (temperature sensor)
Check and or Repair = Remove and replace temperature sensor = AKA thermistor.
Samsung Dryer Error Code = bE
Error Condition = Button is STUCK on control panel
Check and or Repair = Try to free the stuck button by pressing all the buttons on the control panel. If the button stays stuck then replace the user interface control.
Parts For Replacement = User Interface Control
Samsung Dryer Error Code = Od
Error Condition = Excessive (Too Long) drying time
Check and or Repair = Remove power to the dryer. Check the moisture sensor bar and wiring connections. Reconnect any loose wires and replace the wire harness if it has damage. Replace the moisture sensor bar if damage is found.
Parts For Replacement = Moisture Sensor Bar – Wire Harness
Samsung Dryer Error Code = Et
Error Condition = Control board failure
Check and or Repair = Remove power to the dryer for 10 minutes to try and reset the control board. If the error code comes back after restoring the power to your dryer then replace the electronic control board.
Parts For Replacement = Electronic Control Board
Samsung Dryer Error Code = tS
Error Condition = Temperature Sensor = The thermistor is shorted
Check and or Repair = Remove power to the dryer. Test the resistance of the thermistor with a meter. If you find the resistance is over forty thousand ohms then you need to replace the thermistor. If you find the resistance is ten thousand ohms then you need to replace the wire harness if you find it damaged. If the wire harness is not damaged then replace the electronic control board.
Parts For Replacement = Thermistor – Electronic Control Board – Wire Harness
Dryer Thermistor Replacement – Samsung Dryer Repair
Samsung Dryer Error Code = tO
Error Condition = Thermistor is electrically stuck open
Check and or Repair = Remove power to the dryer. Test the resistance of the thermistor with a meter. The thermistor should be ten thousand ohms of resistance at room temp. If the resistance is higher than forty thousand ohms then you need to replace it. If the resistance is normal then check the wire harness and replace it if you find it damaged. If the wire harness is not damaged then replace the electronic control board.
Parts For Replacement = Thermistor – Electronic Control Board – Wire Harness
Repair Samsung Dryer TO (T0) code
Samsung Dryer Error Code = do
Error Condition = Door is in open position
Check and or Repair = Shut the dryer door. If you still have the do error code, remove power to the dryer and check for a loose wiring connection in the door switch. If loose then reconnect the wire harness. Replace the harness if you find damage. If wiring is okay then replace the door switch.
Parts For Replacement = Door Switch – Wire Harness
Samsung Dryer Error Code = FE
Error Condition = Power supply out of range (frequency)
Check and or Repair = If the dryer is getting the power it requires then replace the electronic control board.
Parts For Replacement = Electronic Control Board
Samsung Dryer Error Code = dF
Error Condition = Door has circuit fail
Check and or Repair = Remove power from the dryer. Check for loose wire connections in the door switch. Reconnect a loose or disconnected wire harness. If the wire harness is damaged then replace it. Replace the door switch if you find it to be defective.
Parts For Replacement = Door Switch – Wire Harness
Samsung Dryer Error Code = HE or hE
Error Condition = Heating error issue (FOR GAS DRYER)
Check and or Repair = Be sure the gas supply valve for the dryer is fully in the open position. Remove power to the dryer and if needed reconnect any wiring that is loose. Check wiring connections on the gas valve coils. If the wire harness is damaged replace it.
Parts For Replacement = Wire Harness – Gas Dryer Heat Components
Samsung Dryer Display Panel HE error code
How To Replace Samsung Dryer Heating Element
Samsung Dryer Error Code = HE or hE
Error Condition = Heating error issue (FOR ELECTRIC DRYER)
Check and or Repair = Check to be sure a circuit breaker for the dryer has not tripped. Your dryer will not heat if a breaker of the 240V power supply is turned off. Remove power to the dryer and check the wires on the heat element. Reconnect loose wires and replace the wire harness if it is found to be damaged. Make sure the heat element is not damaged. Replace the heating element if damaged.
Parts For Replacement = Wire Harness – Electric Dryer Heat Element
How to Troubleshoot a Samsung Dryer that is Not Heating
Samsung Dryer Replacement Parts
More clothes dryer troubleshooting for Frigidaire Dryer Error Codes, GE Dryer Error Codes, Kenmore Dryer Error Codes, LG Dryer Error Codes, Maytag Dryer Error Codes, Samsung Dryer Error Codes, and Whirlpool Dryer Error Codes.
If your Samsung Dryer error code is not listed here or you have issues with any Samsung Dryer Error Code, please leave a comment below and we will be happy to assist you with your dryer error code problem.
I have a 2017 Samsung dryer it has a HC code, I replace the heating element with a complete assembly still shows code . I replaced the PCB and the code still shows . Any idea why the code is still showing the only thing I haven’t replaced is the board for the controls. If I replace it I have replaced Ever Electronic Part on the dryer . Do I need to reset it somehow after putting these parts on
How do you clear a code 42 on a Samsung steam moisture sensor dryer?
Im getting an upside down F and a 1 the dryer will not heat. We replaced the heater element and sensors all three of them it worked for about a week and we are back to the same problem what can it be?
What does the timer icon mean on my Samsung moisture sensor dryer mean it’s on and I can’t turn it off and now it’s not heating
Hi..
The red grid lights in my Samsung dryer purchased in 2017 is flashing. When I start a cycle, the actual time-counter works..however, the drum does not rotate and the dryer does not dry/heat. I have cleaned the vents, cleaned the filter.. and still the same problem is there!
The model @ is DV50KB600E
Can you please help?
My samsung dryer model DVE50M7450W heat no longer works..i checked for codes and it shows Clg..vent clogged..i took out lint filter cleaned bottom out.took of vent ducts cleaned them completely out..made sure duct wasnt resticted anywhere and still no heat.and still same Clg code.its onky 5 months old
My dryer is not heating, it runs when you first start it and has full time and then it runs for two minutes and then timer goes to one minute and then shuts off. I have a front loader Samsung model DV42h5200ep/A3
Have model DV220. We had a power surge and now the dryer won’t heat. No error codes. It comes on, turns, etc but no heat.
I had a heavy wet queen size blanket in the dryer before it stopped rotating. The timer continued. The only”code” is a picture of a tee shirt that is flashing with an arrow to another tee shirt that is not flashing and has two wiggle lines going to the middle like maybe it is drying. I checked the lint and turned off the breaker for a good hour. Why if anything do the shirts mean.
I’m not seeing an error code. Cleaned vent hose and seems to have good airflow but won’t heat