Samsung dryer error codes display on your dryer’s control panel to help you troubleshoot the problem. The error codes below will help you to identify what is wrong with your Samsung dryer. Once you have identified the error code, this will tell you which part is causing the issue. You can then check the part in question and clean or replace it if needed. Samsung dryer help videos are here if needed.
Samsung Dryer Error Codes
Samsung Dryer Error Codes
Related to Heating, Voltage, Temperature, Door, Communication, and Jammed Buttons.
Samsung Dryer Heating Errors = HC4, 1 HC, HC, hE
This means that the dryer is getting too hot (overheat).
Samsung Dryer Communication Errors = AE4, AE3, AE5, E3, 1 AC, AC, Et, AE, EEE
This code means the dryer’s internal components are unable to “talk” to each other. Turn off the dryer for 1 minute and turn it back on again.
Samsung Dryer Frequency Errors = 1 FC, FC, FE
These codes mean that there is an power source frequency issue. Restart the cycle to fix this issue.
Samsung Dryer Voltage Errors = 2E, 9E1, 9C1, 9E
This code appears when the voltage is abnormal being supplied to the dryer.
Samsung Dryer Jammed Button Errors = bC2, 6E, 6E2, 6C2, bE, bE2
This code appears if a button on the dryer panel is found to be as stuck or pressed continuously.
Samsung Dryer Door-Related Errors = dF, do, d0, 1 DC, 1 dF, dC, dE
These codes are related to the door, latch, and sensors. These components detect if secured properly. When the door will not stay closed, or won’t close or latch these codes can show.
Samsung Dryer Temperature Errors = tCS, 1 tC, 1tC5, 1tCS, tS, t5, tC, tO, t0, tE, tE3, tC5
The temperature or the sensors have an issue or fault.
Samsung Dryer Vent Blockage Test Results = C80, C8o, C8, C90, C9o, Ct, Clg, Cl9, Cg, C9
The error codes only show after a Vent Blockage test has been ran.
Specific Samsung Dryer Error Codes
Exact error codes to clear or fix your dryer.
Samsung Dryer Error Code = TE
Error Condition = Defective thermistor (temperature sensor)
Check and or Repair = Remove and replace temperature sensor = AKA thermistor.
Samsung Dryer Error Code = bE
Error Condition = Button is STUCK on control panel
Check and or Repair = Try to free the stuck button by pressing all the buttons on the control panel. If the button stays stuck then replace the user interface control.
Parts For Replacement = User Interface Control
Samsung Dryer Error Code = Od
Error Condition = Excessive (Too Long) drying time
Check and or Repair = Remove power to the dryer. Check the moisture sensor bar and wiring connections. Reconnect any loose wires and replace the wire harness if it has damage. Replace the moisture sensor bar if damage is found.
Parts For Replacement = Moisture Sensor Bar – Wire Harness
Samsung Dryer Error Code = Et
Error Condition = Control board failure
Check and or Repair = Remove power to the dryer for 10 minutes to try and reset the control board. If the error code comes back after restoring the power to your dryer then replace the electronic control board.
Parts For Replacement = Electronic Control Board
Samsung Dryer Error Code = tS
Error Condition = Temperature Sensor = The thermistor is shorted
Check and or Repair = Remove power to the dryer. Test the resistance of the thermistor with a meter. If you find the resistance is over forty thousand ohms then you need to replace the thermistor. If you find the resistance is ten thousand ohms then you need to replace the wire harness if you find it damaged. If the wire harness is not damaged then replace the electronic control board.
Parts For Replacement = Thermistor – Electronic Control Board – Wire Harness
Dryer Thermistor Replacement – Samsung Dryer Repair
Samsung Dryer Error Code = tO
Error Condition = Thermistor is electrically stuck open
Check and or Repair = Remove power to the dryer. Test the resistance of the thermistor with a meter. The thermistor should be ten thousand ohms of resistance at room temp. If the resistance is higher than forty thousand ohms then you need to replace it. If the resistance is normal then check the wire harness and replace it if you find it damaged. If the wire harness is not damaged then replace the electronic control board.
Parts For Replacement = Thermistor – Electronic Control Board – Wire Harness
Repair Samsung Dryer TO (T0) code
Samsung Dryer Error Code = do
Error Condition = Door is in open position
Check and or Repair = Shut the dryer door. If you still have the do error code, remove power to the dryer and check for a loose wiring connection in the door switch. If loose then reconnect the wire harness. Replace the harness if you find damage. If wiring is okay then replace the door switch.
Parts For Replacement = Door Switch – Wire Harness
Samsung Dryer Error Code = FE
Error Condition = Power supply out of range (frequency)
Check and or Repair = If the dryer is getting the power it requires then replace the electronic control board.
Parts For Replacement = Electronic Control Board
Samsung Dryer Error Code = dF
Error Condition = Door has circuit fail
Check and or Repair = Remove power from the dryer. Check for loose wire connections in the door switch. Reconnect a loose or disconnected wire harness. If the wire harness is damaged then replace it. Replace the door switch if you find it to be defective.
Parts For Replacement = Door Switch – Wire Harness
Samsung Dryer Error Code = HE or hE
Error Condition = Heating error issue (FOR GAS DRYER)
Check and or Repair = Be sure the gas supply valve for the dryer is fully in the open position. Remove power to the dryer and if needed reconnect any wiring that is loose. Check wiring connections on the gas valve coils. If the wire harness is damaged replace it.
Parts For Replacement = Wire Harness – Gas Dryer Heat Components
Samsung Dryer Display Panel HE error code
How To Replace Samsung Dryer Heating Element
Samsung Dryer Error Code = HE or hE
Error Condition = Heating error issue (FOR ELECTRIC DRYER)
Check and or Repair = Check to be sure a circuit breaker for the dryer has not tripped. Your dryer will not heat if a breaker of the 240V power supply is turned off. Remove power to the dryer and check the wires on the heat element. Reconnect loose wires and replace the wire harness if it is found to be damaged. Make sure the heat element is not damaged. Replace the heating element if damaged.
Parts For Replacement = Wire Harness – Electric Dryer Heat Element
How to Troubleshoot a Samsung Dryer that is Not Heating
Samsung Dryer Replacement Parts
More clothes dryer troubleshooting for Frigidaire Dryer Error Codes, GE Dryer Error Codes, Kenmore Dryer Error Codes, LG Dryer Error Codes, Maytag Dryer Error Codes, Samsung Dryer Error Codes, and Whirlpool Dryer Error Codes.
If your Samsung Dryer error code is not listed here or you have issues with any Samsung Dryer Error Code, please leave a comment below and we will be happy to assist you with your dryer error code problem.
What if i have a 60Hz Dryer and i am in Europe on 50Hz, is there a replacement board or a converter that doesn’t cost too much?
Scott klingman,
Error t0 is an open thermistor on Samsung dryers. Thermistor should measure 10,000 ohms at 77 degrees fahrenheit.
Check it at the blower with one side disconnected and if OKAY, check it at the plug on the control board.
-RR
Samsung Dryer code is showing tO. Don’t know if that’s any different. Didn’t have an ohm meter but continuity is positive. I was assuming if the dial was stuck open there would be no continuity.
Tara Blackburn,
First, be sure the dryer door is properly closed and the lint filter is properly installed…
The Samsung Dryer Eg Or E9 Error Code is not actually an error code. It is a code displayed when the dryer is in the test mode used on the production line. This error can appear when certain buttons are pushed at the same time or in a certain sequence. To exit this and clear the E9 error, unplug the dryer from power for 10 seconds and then plug back in. You can also flip the breaker to the dryer if it is difficult to access the plug.
-RR
Samsung Dryer Error code E9? Hope you can help!
Jose,
DE Error on Samsung dryer means that “door is open”. The dryer thinks the door is open. It is probable that power is not getting passed from the door switch to the control board. Check the door switch assembly to be sure the wire harness is connected and that it is not damaged. If damaged, replace it with an OEM part.
-RR
My dryer is giving me a DE error message and I can’t find the code any where online. Please let me know what I can do?
Shila,
Samsung Dryer FE error code = Power supply frequency is out of range
Check the frequency of your electrical power supply.
If the dryer is getting the 60 Hz power it requires, replace the electronic control board.
-RR
I have recently changed my plug due to it being faulty. It works just fine for the washer…but when comes to dryer it give me the FE code. Let me know on how to go about.
Barry S. Jameson,
Try unplugging the Samsung dryer for 5 minutes.
Also, please supply us with the dryer model number so we can find the information needed to fix your Samsung dryer.
Is the door switch damaged or is the not shutting properly?
-RR