Here is a list of washer error codes for Logik Washing Machines. If you cannot find your error code below, go to the bottom of the page and ask us. We will be happy to assist you with your washing machine error code and can help you to troubleshoot your specific washing machine issue. If your washer error code is found below, this error list will tell you what part is faulty or has failed. This list is based on the washing machine manufacturers list of error codes. NOTE: There are different model numbers that correspond with the error codes below, make sure the washer error code applies to your washer model number before doing any repairs.
LOGIK Washing Machine Error Codes
Logik Washing Machine Error 02:
Error Code Definition: The water level in your machine is below the heater. The pressure of your water may be too low.
Logik Washing Machine Error 03:
Error Code Definition: The pump had failed or the pump is obstructed.
Logik Washing Machine Error 05:
Error Code Definition: The heater or heat sensor has failed.
Logik Washing Machine Error 06:
Error Code Definition: The motor has failed.
More Logik Washer Error Codes with “How To Clear &Â What To Check To Fix”…
Logik Washing Machine Error 10: “E10”
Error Code Definition: Water drain time out or failure
The washing machine has failed to drain the water in allotted time (6 minutes).
How To Clear Error Code:
-Check that filter is not blocked or kinked
-Check drain hose is clear of blockage or kinks
-Check wires to drain pump
-Check drain pump is not faulty
-Check level sensor and switch
-Check wires to level sensor
Logik Washing Machine Error 12: “E12”
Error Code Definition: Washing machine has detected overfill.
This error code can be caused by oversudsing from overloading or by adding too much detergent.
The pressure sensor will read that there is too much water in the washer.
How To Clear Error Code:
-Check for sudsing
-Check the air chamber & the pressure switch hose
-Check water level sensor
-Check the wiring to water pressure sensor
-Check connections to water level sensor
-Check main electronic control board
Logik Washing Machine Error 21: “E21”
Error Code Definition: Washer has not drained in allotted / time washer not draining.
How To Clear Error Code:
-Check that filter is not blocked or kinked
-Check drain hose is clear of any blockage or kinked
-Check wires to drain pump
-Check drain pump is not faulty
-Check level sensor and switch
-Check wires to level sensor
Logik Washing Machine Error 30: “E30”
Error Code Definition: Washer door lock not operational operate and or not responding.
Error with the door safety lock switch or interlock prevent operation.
How To Clear Error Code:
-Check that door is closed and shut properly
-Check wires to door switch
-Check door lock for faults
Logik Washing Machine Error 30: “E60”
Error Code Definition: Washer motor failure or fault.
Washers main drive motor circuit error.
How To Clear Error Code:
-Check motor connection block
-Check motor carbon brushes to see if worn
-Check wires
-Check tachometer connections
-Check motor for other faults
Logik Washing Machine Error 61: “E61”
Error Code Definition: Motor tachometer generator fail.
Error on the washers main drive motor circuit in connection with overheat protector in the motor.
How To Clear Error Code:
-Check motor connection block
-Check motor carbon brushes for wear
-Check wiring
-Check tachometer connections
-Check motor for other faults
LOGIK washing machine spare parts – Replacement Parts
Need help with your Logik Washing Machine and Error Codes? Please leave your question below and we will be happy to assist.
Check your filter in the pump, (Bottom Right Front of machine) for coins, clips, hair or any debris no matter how small. Check drain hose for blockages and if connected to a U bend on the sink, check U bend for blockages. You WILL find you answer there.
This to me sounds like a heater problem. If your heating element is faulty and the program is waiting for the water to heat up to desired/programmed temp. Because the heater is faulty, water will NEVER reach temperature. So, the program will NOT progress forward until the water does. The program will therefore wait and wait and wait and wait….
Logik L612WM13 Washing Machine. “E30” error code displayed=(door lock not operational or not responding). Removed door lock and identified 3 terminals L, N and C. Applied 240v across L and N and used Digital MultiMeter across C and N whereby under lock conditions, 240V is read on DMM. On the machine also, door DOES lock as normal. There is a burn mark on the pcb “S3” spade connector (that has a black coloured connector block). The connector was loose fitting but is now a tight fit. Burn mark connects to thick GREY wire which connects pcb to the pressure switch. All capacitors are visually okay, no signs of burnt resistors, no holes in triacs, no other signs of burning on the the pcb. All relays desoldered and 12v DC applied across coils, contacts DO switch over according to my DMM. So what now? I am baffled. Could this be a faulty pressure switch, motor brushes worn down, mains filter failure,…I don’t know where to go next. No info online other than error code listings.
hi. L612WM16 model.
was working fine. drainage pipe sliped off. i put it back. then too forever to fininh. now wont drain at all or function. lock sign is on. dounds like its trying to drain. i checked pipe again and its running though ok. so im stumped?
My Logik L612WM13 wash machine stops in the middle of the programme it’s set on, and does the exact cycle forever, any hints on how could i reset it to default?
I have a Logik L612WMS13 washing machine
And for some reason it will wash on a cycle but will not spin.
Also will not spin on just a spin cycle or a rinse and spin.
So basically it will not go into spin mode at all. But it is not showing any kind of error code.
It showes 0:01 and is locked both child lock and wash lock with my clothes inside how do I unlock of fix this
Keep getting an error code e
What is the problem
Model L612wm13
Taking 2 hours to do a wash ??
hi ive got a L714wm12E and its been working fine for a while,it starts the program and only spins once then stops spinning when i start the wash,when i pause and restart the wash it only spins once again then stops again.there is no error code displayed.any help would be greatly appreciated.thanks
After mine was repaired for a E4 error it started giving me a E8 error instead. Not sure, but it seems to be at the end or just after its finnished washing the dishes. ( E8 is not in the manual or anywhere I can find using google). The dishwasher is a “Logik LDW45W16N”.