5 Ways To Fix Bosch Dishwasher E24 Error Code

Error code e24 Bosch! Is your Bosch dishwasher displaying the E24 error code? The culprit behind this issue can vary, but a clogged drain pump is a common trigger. When the drain pump gets blocked, it can’t effectively remove wastewater, resulting in the E24 code. You can fix it in 5 simple ways.

Another potential cause is a faulty drain hose that fails to properly channel water out of the dishwasher. Accumulated debris in the dishwasher filter can also lead to the E24 error.

1. Reset the dishwasher
2. Clean the filter
3. Inspect drain pump
4. Drain hose clogged
5. Water sensor problem

1. How To Reset Dishwasher

Resetting your dishwasher can often resolve common error codes like E24. By power cycling the appliance and initiating a reset, you give it a chance to clear any temporary glitches or malfunctions that may be causing the error.

1. Start by turning off the power to your dishwasher at the wall socket and unplugging it from the outlet.
2. Leave it unplugged for a few minutes to ensure a complete power cycle. This helps in resetting its internal components.
3. After waiting for a few minutes, plug in your dishwasher again and make sure it is securely connected to the power source.
4. Press and hold down the Start button on your dishwasher control panel.
5. Keep holding it until you see signs of a reset, such as lights flashing or an audible beep.

If you’re unsure about how to perform a reset on your specific Bosch dishwasher model, refer to the bosch dishwasher user manual provided with your appliance. The manual will provide step-by-step instructions tailored specifically for your model.

2. Clean Dishwasher Filter

1. Remove and rinse out the dishwasher filter under running water. Make sure to detach it carefully to avoid damaging any parts.
2. Check for trapped food particles or debris in the filter housing. It’s common for dirt, fine particles, and even foreign objects to accumulate over time.
3. Reinstall the clean filter back into its original position securely. Ensure it fits snugly, so it effectively filters out any remaining dirt during future wash cycles.

To clean your dishwasher filter effectively, you don’t need any fancy cleaning solutions or products. All you need is some vinegar and water. Mix equal parts vinegar and water in a container and soak the water filter in this solution for about 15 minutes. Then, scrub away any stubborn dirt or debris using a soft brush or toothbrush.

3. Checking Drain Pump

To solve the Bosch dishwasher error code E24, start by checking the drain pump. Follow these steps:

1. Find the drain pump at the bottom of the dishwasher.
2. Inspect the pump impeller and drain filter for any blockages or foreign objects.
3. Remove the drain pump cover to access the impeller area.
4. Manually rotate the pump to test its functionality.
5. If there is resistance or it doesn’t rotate smoothly, there may be a problem with the pump motor.

4. Checking Drain Hose

If you’re facing the Bosch dishwasher error code E24, it’s time to check the drain hose. Here are a few steps to help you solve this issue:

1. Examine the drain hose: Take a close look at the drain hose for any kinks, bends, or obstructions. These can prevent proper water flow and cause the error code to appear.
2. Ensure proper connections: Make sure that the hose is securely connected to both the dishwasher and sink drain. Loose or improper connections can lead to drainage problems.
3. Clear any clogs: If there are blockages in the hose, use a plumber’s snake or wire to clear them out. Clogged air gaps or holes in the hose can disrupt water flow and trigger error codes.
4. Check for excess water: Look for any signs of excess water around the dishwasher or under your sink. This could indicate a blockage or failure in draining properly.

5. Water Level Sensor Issue

The sensor responsible for detecting the correct water level in the dishwasher can also contribute to an E24 error. If this sensor malfunctions it may inaccurately detect the water level, causing the dishwasher to display the E24 error.

Check the water sensor in your dishwasher, follow these steps:

1. Find the water level sensor near the bottom of the dishwasher. It could be a small tube or probe in the water.
2. Check for blockages caused by debris or food. Clean it well if you find any.
3. Run a dishwasher cycle and watch the water level. If it’s too low or too high, the sensor might be broken and needs replacing.
4. Make sure the wiring is connected correctly. If the sensor is broken, order a new one from Bosch.

If you’re still experiencing difficulties with your Bosch dishwasher or have any other questions regarding its operation, maintenance or Bosch dishwasher error codes, don’t hesitate to reach out to our customer support team for assistance.

Q: Can I fix the E24 error code myself?

A: Yes, you can try troubleshooting steps like resetting the dishwasher, checking the drain pump and hose, as well as cleaning the filter.

Q: How often should I clean my dishwasher filter?

A: It is recommended to clean your dishwasher filter at least once every month to ensure optimal performance and prevent clogs.

Q: Can using the wrong detergent cause the E24 error code?

A: Yes, using improper or excessive detergent can lead to drainage issues and trigger the E24 error. Make sure to use the recommended dishwasher detergent in appropriate amounts.