A pair of headphones with audio cutting out on one side can be a common problem. Often, the issue is a broken or damaged wire near the plug or inside the ear cup. This guide provides an easy, do-it-yourself approach to repairing those wires and restoring your headphones’ full sound.
Step 1: Confirm the Source of the Issue
• Test your headphones on more than one device (phone, computer, etc.).
• If the same side is silent no matter the device, the headphones themselves need repair.
• If the problem shifts from left to right depending on the device or jack, the issue may be related to the audio source rather than the headphones.
Step 2: Gather Your Tools
• Soldering iron (small, low-wattage)
• Solder (rosin-core is usually recommended for electronics)
• Wire strippers or a sharp knife
• Heat-shrink tubing or electrical tape
• Small screwdriver set (if you need to open the ear cup)
• Replacement headphone plug (if the current plug is damaged)
Step 3: Inspect the Headphone Cable
Check for visible signs of wear or damage along the cable:
• Frayed wiring
• Bends or kinks near the plug
• Bare copper showing through the insulation
These trouble spots often indicate where the sound may be cutting out. Gently move and flex the wire while playing audio to see if there’s an intermittent connection.
Step 4: Repair or Replace the Plug (Most Common Fix)
- Cut and Strip the Cable
Remove the faulty or damaged plug by slicing the cable a couple of inches above the plug. Use wire strippers to remove about half an inch of insulation from the cable’s end, revealing two or three internal wires. - Identify Internal Wires
Headphone cables typically have left (L), right (R), and ground (common) wires. They may be color-coded (red for right, green or blue for left, and bare/copper for ground), or they might have enamel coatings in place of traditional insulation. - Prep the Wires
If your wires have an enamel coating, carefully burn off or strip away the coating with the soldering iron or fine sandpaper. Twist the same-color strands together, making sure they’re neat. - Solder New Plug
Disassemble the replacement headphone plug so you can see the terminals inside. Typically:
• Tip: Left (L)
• Ring: Right (R)
• Sleeve: Ground (common)
Heat each terminal briefly with the soldering iron, then apply a small amount of solder. Insert the correct wire (L, R, Ground) into each terminal and heat it again so the solder flows around the wire. - Insulate and Reassemble
Slide heat-shrink tubing over each solder joint or use electrical tape to prevent short circuits. Reassemble the plug housing, making sure no wires touch each other improperly.
Step 5: Inspect Wiring Inside the Ear Cup (If Needed)
If replacing or repairing the plug doesn’t fix the problem, the wiring inside one ear cup could be damaged.
- Use the appropriate screwdriver to remove any screws.
- Gently open the cup, watching for thin wires.
- Look for loose or broken connections where wires attach to the speaker driver.
- Solder any disconnected wires back into place. If the solder pads on the driver are labeled (+/- or L/R), match the wire colors accordingly.
Step 6: Test Your Work
• Plug the headphones into an audio source at a low volume to check that both sides work.
• Lightly wiggle the cable near the solder points and plug to ensure there is no crackling or cutout.
Links to the most popular headphone manufacturers: Beats, Bose, Klipsch, Master & Dynamic, Monster, Philips, Sennheiser, Skullcandy, and Sony.
Safety Reminders
Turn off and unplug your soldering iron after use.
Allow the iron to cool on a heat-resistant stand before storing it.
Work in a well-ventilated area to avoid breathing in solder fumes.
Repairing headphones that only have sound on one side typically involves finding and fixing a faulty connection. In many cases, re-soldering or replacing the plug solves the problem. If the trouble remains, it could be inside the ear cup wiring, which can also be repaired with a careful approach. With a few simple tools, a bit of patience, and the right guidance, you can restore stereo sound to your favorite headphones without having to buy a new pair.
Do you have an easier way to fix audio issues on a pair of headphones? Please leave a comment below.
Written by Keith Schneerer
Certified Appliance Tech · Founder, RemoveAndReplace.com
Keith has spent 30+ years repairing machines, starting as a military mechanic and later maintaining food processing equipment before moving into appliance repair. He founded RemoveAndReplace.com to share field-tested repair advice.
More about Keith →
I’ve tried bending it multiple times but every time there’s a different spot where bending it produces a short period of sound
This is not an easy fix. There HAS to be a way to get the sound back without cracking our headphones open and soddering anything. There HAS to be a better way other than shelling out cash for a new headphone.
My Bose headphones qc35 stoped working on the left side and i have tried to go to diffrent cords but it still doesn’t work
Bhavesh,
The left earbud works but it is not as loud as the right earbud?
Is the wire damaged or twisted?
Any sign of a problem on the wiring or the earbud itself?
What was the cost of your leeco lepdh401IN CDLA earphones?
-RR
I have leeco lepdh401IN CDLA earphones I had just dropped it but still it was working fine but after some days I could just hear the left earbud’s sound but with low intensity while right earbud was working perfect.what should I do please help.
Thank you for the reply, I apologize for this mistake, my headphones is ATH WS550. I tried opening the left and right earcups (not sure if this is the right term) , but everything is fine, the wires are soldered ok.
Gerard,
The Audio Technica ATH M550 Headphones are expensive.
When the cord has a short, we recommend to purchase a new cord instead of attempting to fix the short.
Check here for a few different cords for your headphones around 20 US dollars each or less.
Audio Technica Headphone Replacement Cords
-RR