Trying to wash your clothes but your washing machine will not agitate or wash? If your washing machine fills with water but then stops, here is the best tip to fix it fast. If you have a top loading washer, the MOST likely part to have failed is the LID SWITCH. Before anything make sure that you have the lid shut. The machine will not run if the lid is open. This is a safety feature so the machine will not agitate with the lid in the open position. Many times we can get into a rush and forget to shut the lid. If you have the lid shut and the machine has only filled with water and stopped, read on below. (If your washer is NOT SPINNING DRAINING, click here.)
Your top load washing machine has a safety feature built in that will not let it agitate or wash if the lid is open. If the lid switch in your washing machine goes bad, the washer will think the lid is in the open position. This will cause the machine to not do anything after it fills with water. If the lid switch is bad, having the lid either open or closed will make no difference. If the washing machine has power, has filled with water, then stops, makes no noise, then the lid switch is most likely the part that needs replaced.
The best thing to do at this point is to get the make and model number of your washing machine and type it into Google. Write the words “lid switch” after it and find the exact part for your machine online. Order it next day air and install it with the instructions included. If this did not fix your washer, there is another part that has failed. See below.
VIDEO: Troubleshooting why your washing machine is not agitating
The lid switch is the most likely part to fail in this circumstance. However, this is only the most likely and there may be another part at fault. Here is a short list of ALL the parts in your top load washer that may have failed (and caused your particular problem) in alphabetical order…
- Cycle Selector Switch – The cycle selector switch controls the speed of the motor and if it goes bad it can stop the motor from operating.
- Drive Belt – If the belt falls off or becomes worn the transmission will not turn and the machine will not agitate. The machine will make a humming noise as the motor will be running.
- Drive Motor – This motor turns the agitator and drum to wash your clothing. If it goes bad the machine will not agitate.
- Lid Switch – The lid switch makes it so if the lid is opened, the machine will not run. A bad lid switch will make it so power cannot get to the drive motor.
- Timer – The timer supplies power to turn the motor. If the timer is defective, the motor will not turn therefore no washer agitation.
- Water Level Switch – The water level switch (aka Pressure Switch) controls the water level. If defective the motor may not receive power.
These are the most likely parts that may have failed due to the issue we have explained above. Use safety precautions when doing any type of maintenance checks on your washer.
Not all top loading washing machines work in the same way. Some have different parts and operating functions. This guide shows the most basic and general method of fixing most top load washers.
Written by Keith Schneerer
Certified Appliance Tech · Founder, RemoveAndReplace.com
Keith has spent 30+ years repairing machines, starting as a military mechanic and later maintaining food processing equipment before moving into appliance repair. He founded RemoveAndReplace.com to share field-tested repair advice.
More about Keith →
Samsung WA65F5S2URW 6.5kg Top Load Washing Machine – it fills with water … then hums but does not agitate ?
I have a KitchenAid (Whirlpool) KAWS700G that will fill but then does nothing. It’s dead silent. I’ve changed the Timer, Water Level Switch, Lid Switch, Capacitor, Transmission and Motor. All the wires look good and all connections are tight. Connections look good. No burned contact points.
Any suggestions would be greatly appreciated.
Thank You
My Maytag top loader washer lid has to be pushed in and held for the spin cycle to work. I replaced the locking mechanism but it didn’t help. I have to put a rag in the door and push back on the lid. It’s about 4 years old.
Hi I have bought a 10.5kg whirlpool brand washing but suddenly it just stop working. When we on the machine the water gets filled. Not even goes to wash it remains on sensing. Can some one help me out here cause I have a trust in Whirlpool brand and I have all the appliance of the same brand.
I have a Kenmore top-loading washing machine.
The sensing button lights up the water starts to fill slowly but will not completely fill then the water starts to drain before it is completely filled and then the sensor light comes back on again.
It never gets to agitate because it’s not filling up.
I have a top and bottom washer and dryer and the washer will fill with water then just sit full without agitating or moving the articles of clothing.
Once the timer reaches the rinse and spin cycle it will run normally draining the water and rinsing with fresh and draining again.
It will not actually wash my clothing.
Once the water has filled it will remain still until the timer reaches rinse and spin.
Which part needs to be replaced?
I have a top loader maytag centennial washer. It will not agitate. It fills and spins fine but isn’t agitating. The lid switch works and will start the water and stop it normally. Can you help?