I have a Whirlpool Cabrio washer about a year old. When I run a wash cycle it gets stuck in constant loop of wash cycles going on and on. The washer would begin to soak the clothes right after the spin cycle and then go through the entire wash cycle once again. To stop this I had to turn the washer off. Is there a reset I could follow to stop the endless wash cycle or do I need to replace parts?
Whirlpool Cabrio Washer Stuck In Wash Loop – How To Reset
Yes, there is a reset procedure to fix this. The Whirlpool Cabrio washers need to be reset in a different method than many other types and brands of washers. Here is how you can RESET your Cabrio washer (all Whirlpool Cabrio models). Follow the directions below and your washer should reset and begin to work normally. This reset procedure works on ALL Whirlpool Cabrio Washers that start with model number WTW.
How To Reset Whirlpool Cabrio Washer:
- Turn the washer off.
- Set the mode selector dial to NORMAL.
- Turn the dial counter clockwise ONE click (LEFT), clockwise THREE clicks (RIGHT), counter clockwise ONE click (LEFT) then clockwise ONE click (RIGHT).
- Now press the start button.
- All the cycle indicating lights should be illuminated.
- Press the Start Stop button once.
- Rotate the dial until Rinse, Wash, and Stop light illuminate.
- Turn the washer off and unplug it for 10 seconds.
- Finally, turn on the washer and it should now be reset.
- Run a test load empty to be sure the reset worked. If not perform the reset procedure one more time.
Whirlpool Cabrio Washing Machine Replacement Parts WTW
If that did not work, try the next Cabrio reset procedure:
- Touch any button on the display pad to clear the error code or press “Pause Cancel.”
- Choose another cycle and press “Start”.
- Disconnect the Cabrio from power if the error or problem comes back.
- Wait 5 minutes before restoring power.
- Choose a new cycle and press “Start.”
- Run a test load empty to be sure the reset worked. If not perform the reset procedure one more time.
Cabrio Washing Machine Diagnostic Test & Error Codes
If the second reset does not get your washer out of the endless wash cycle, please leave a comment below and explain in detail what the exact issue is and we will assist in troubleshooting.
Written by Keith Schneerer
Certified Appliance Tech · Founder, RemoveAndReplace.com
Keith has spent 30+ years repairing machines, starting as a military mechanic and later maintaining food processing equipment before moving into appliance repair. He founded RemoveAndReplace.com to share field-tested repair advice.
More about Keith →
Whirlpool Cabrio model w TW 6 8 00 w w one washing machine shuts off 10 minutes before spins out
Cabrio wtw6600sw0 shows error code oL after the washer fills up with water.
But won’t wash because of error code oL and we just put new balance springs thinking that would solve it.
Then replaced the stater and that didn’t work, and now we just replaced the rps system and the code still pops up and we also tried resetting the control board.
Still error code oL can anyone help us out!
Now it’s filling up then goes straight into drain mode.
I have a whirlpool fabric washer. For instance I put it on quick load for 33 minutes. It stop at 24 and constantly run can you tell me what’s the problem
Misty Miller,
You may have a drain pump issue.
Check that the drain pump is not blocked and check that the drain hose is not clogged.
If the washer checks good, the issue could be in the wall… Wall drain is blocked possibly.
-RR
Cabrio washer keeps going from 39 min cycle back to 1:03 cycle.
My washer seems to not be spinning the water out.
I have done the reset thing and it still isn’t working.
Okay, so when I start the washing machine and press the start button the sensing water light will come on and start to fill up with water, but after a little bit of water in the washer it will start draining the water out. Please help