Samsung dryer error codes display on your dryer’s control panel to help you troubleshoot the problem. The error codes below will help you to identify what is wrong with your Samsung dryer. Once you have identified the error code, this will tell you which part is causing the issue. You can then check the part in question and clean or replace it if needed. Samsung dryer help videos are here if needed.
Samsung Dryer Error Codes
Samsung Dryer Error Codes
Related to Heating, Voltage, Temperature, Door, Communication, and Jammed Buttons.
Samsung Dryer Heating Errors = HC4, 1 HC, HC, hE
This means that the dryer is getting too hot (overheat).
Samsung Dryer Communication Errors = AE4, AE3, AE5, E3, 1 AC, AC, Et, AE, EEE
This code means the dryer’s internal components are unable to “talk” to each other. Turn off the dryer for 1 minute and turn it back on again.
Samsung Dryer Frequency Errors = 1 FC, FC, FE
These codes mean that there is an power source frequency issue. Restart the cycle to fix this issue.
Samsung Dryer Voltage Errors = 2E, 9E1, 9C1, 9E
This code appears when the voltage is abnormal being supplied to the dryer.
Samsung Dryer Jammed Button Errors = bC2, 6E, 6E2, 6C2, bE, bE2
This code appears if a button on the dryer panel is found to be as stuck or pressed continuously.
Samsung Dryer Door-Related Errors = dF, do, d0, 1 DC, 1 dF, dC, dE
These codes are related to the door, latch, and sensors. These components detect if secured properly. When the door will not stay closed, or won’t close or latch these codes can show.
Samsung Dryer Temperature Errors = tCS, 1 tC, 1tC5, 1tCS, tS, t5, tC, tO, t0, tE, tE3, tC5
The temperature or the sensors have an issue or fault.
Samsung Dryer Vent Blockage Test Results = C80, C8o, C8, C90, C9o, Ct, Clg, Cl9, Cg, C9
The error codes only show after a Vent Blockage test has been ran.
Specific Samsung Dryer Error Codes
Exact error codes to clear or fix your dryer.
Samsung Dryer Error Code = TE
Error Condition = Defective thermistor (temperature sensor)
Check and or Repair = Remove and replace temperature sensor = AKA thermistor.
Samsung Dryer Error Code = bE
Error Condition = Button is STUCK on control panel
Check and or Repair = Try to free the stuck button by pressing all the buttons on the control panel. If the button stays stuck then replace the user interface control.
Parts For Replacement = User Interface Control
Samsung Dryer Error Code = Od
Error Condition = Excessive (Too Long) drying time
Check and or Repair = Remove power to the dryer. Check the moisture sensor bar and wiring connections. Reconnect any loose wires and replace the wire harness if it has damage. Replace the moisture sensor bar if damage is found.
Parts For Replacement = Moisture Sensor Bar – Wire Harness
Samsung Dryer Error Code = Et
Error Condition = Control board failure
Check and or Repair = Remove power to the dryer for 10 minutes to try and reset the control board. If the error code comes back after restoring the power to your dryer then replace the electronic control board.
Parts For Replacement = Electronic Control Board
Samsung Dryer Error Code = tS
Error Condition = Temperature Sensor = The thermistor is shorted
Check and or Repair = Remove power to the dryer. Test the resistance of the thermistor with a meter. If you find the resistance is over forty thousand ohms then you need to replace the thermistor. If you find the resistance is ten thousand ohms then you need to replace the wire harness if you find it damaged. If the wire harness is not damaged then replace the electronic control board.
Parts For Replacement = Thermistor – Electronic Control Board – Wire Harness
Dryer Thermistor Replacement – Samsung Dryer Repair
Samsung Dryer Error Code = tO
Error Condition = Thermistor is electrically stuck open
Check and or Repair = Remove power to the dryer. Test the resistance of the thermistor with a meter. The thermistor should be ten thousand ohms of resistance at room temp. If the resistance is higher than forty thousand ohms then you need to replace it. If the resistance is normal then check the wire harness and replace it if you find it damaged. If the wire harness is not damaged then replace the electronic control board.
Parts For Replacement = Thermistor – Electronic Control Board – Wire Harness
Repair Samsung Dryer TO (T0) code
Samsung Dryer Error Code = do
Error Condition = Door is in open position
Check and or Repair = Shut the dryer door. If you still have the do error code, remove power to the dryer and check for a loose wiring connection in the door switch. If loose then reconnect the wire harness. Replace the harness if you find damage. If wiring is okay then replace the door switch.
Parts For Replacement = Door Switch – Wire Harness
Samsung Dryer Error Code = FE
Error Condition = Power supply out of range (frequency)
Check and or Repair = If the dryer is getting the power it requires then replace the electronic control board.
Parts For Replacement = Electronic Control Board
Samsung Dryer Error Code = dF
Error Condition = Door has circuit fail
Check and or Repair = Remove power from the dryer. Check for loose wire connections in the door switch. Reconnect a loose or disconnected wire harness. If the wire harness is damaged then replace it. Replace the door switch if you find it to be defective.
Parts For Replacement = Door Switch – Wire Harness
Samsung Dryer Error Code = HE or hE
Error Condition = Heating error issue (FOR GAS DRYER)
Check and or Repair = Be sure the gas supply valve for the dryer is fully in the open position. Remove power to the dryer and if needed reconnect any wiring that is loose. Check wiring connections on the gas valve coils. If the wire harness is damaged replace it.
Parts For Replacement = Wire Harness – Gas Dryer Heat Components
Samsung Dryer Display Panel HE error code
How To Replace Samsung Dryer Heating Element
Samsung Dryer Error Code = HE or hE
Error Condition = Heating error issue (FOR ELECTRIC DRYER)
Check and or Repair = Check to be sure a circuit breaker for the dryer has not tripped. Your dryer will not heat if a breaker of the 240V power supply is turned off. Remove power to the dryer and check the wires on the heat element. Reconnect loose wires and replace the wire harness if it is found to be damaged. Make sure the heat element is not damaged. Replace the heating element if damaged.
Parts For Replacement = Wire Harness – Electric Dryer Heat Element
How to Troubleshoot a Samsung Dryer that is Not Heating
Samsung Dryer Replacement Parts
More clothes dryer troubleshooting for Frigidaire Dryer Error Codes, GE Dryer Error Codes, Kenmore Dryer Error Codes, LG Dryer Error Codes, Maytag Dryer Error Codes, Samsung Dryer Error Codes, and Whirlpool Dryer Error Codes.
If your Samsung Dryer error code is not listed here or you have issues with any Samsung Dryer Error Code, please leave a comment below and we will be happy to assist you with your dryer error code problem.
My Samsung Dryer error code is not listed. It looks like EE but the e at the beginning is missing the top, it is like an upside down F?
I had the HE error code on my Samsung DV8 dryer.
After cleaning the filters I took it apart and checked the 2 thermistors (~50k ohm) and they appeared to be ok as well as anything else.
Put it together again and started it.
Same HE error code again.
I then switched the machine off and held the light-button while turning it on.
The dryer then made a self-test and displayed “b2”.
I turned it off and on again and the code was gone. Yeeha!
Hope it works for you too!!!
For the past few days my year-old Samsung dryer DV52J8700E(G) has been stopping before the clothes are dry–both on timed and regular cycles. Finally got a vent clog icon. Cleaned, vacuumed and reattached vent hose and outside vent. Restarted after 20 minutes. Pulled out from wall in case hose was squeezed. Stopped again. Code upside-down FC. Help?
Dryer changed heating element assembly still getting H E and not working
Hi Phil I seem to have a very similar problem. HE error code. My dryer is a DV80H8100HW (heat pump dryer.) If you ever do find a solution to this problem please do let me know! I have replaced the thermistor already as well but to no help.
Yes the Samsung dryer is brand new, but I have taken it overseas, hence the company that sold it to me cannot help me. The model is a DV80H8100HW (Heat Pump Dryer.) Serial number I’m afraid I don’t have right now as I’m not at home. I can get it if it’s really necessary. I have modified the cabinet so that there is much more airflow now so I don’t think that will be a problem in the future. But alas the dryer is still not working and still has the HE code. As mentioned before the thermistor has already been replaced.
I have model DV210AEW dryer. I have replaced and tested every part of the heating side of the system. I am still getting a HE code on the screen. I replaced the thermostat, high temp sensor and the Assy Pcb Main board and tested the heating coil and it was good.
Geoff Cattrall,
If the Samsung dryer is brand new, why not call the company that sold it to you and have it replaced or fixed?
You may have a completely different dryer configuration than we realized.
Can you give us the full model number and serial number so we can research further?
And yes, the dryer needs some air flow to be able to run properly, that may or may not cause the HE code.
How much space does the dryer have inside the cabinet?
-RR
HI there… yes I am still getting the HE error code even after replacing the thermistor. The dryer will not run – in fact no functions are available. When I turn the dryer on there is an HE code on the screen and I cannot select a cycle, run the dryer, or do anything. The only thing I can do at that stage is turn the dryer off again. I have checked all wiring as far as I can see with the top, front and back off and it looks ok. Please note that this is a brand new unit. Since it was running in a cabinet with poor airflow, I agree there is a good chance it’s a heating element problem of some sort. But this is a Heat Pump dryer – does it even have a heating element? Or is it a compressor? And how can I access this part of the dryer? I’m not sure how to check ‘the element is not shorted’. I don’t see anything that looks like a compressor or heating element on the front of the unit. Any and all advice appreciated thanks!
Neil Brodsky,
Samsung dryer “dC” flashing error code is not in the database.
The DC error code is listed as a Samsung washer unbalanced load. You may have overloaded the dryer with the towels.
Can you supply us with your Samsung Dryer Model Number so we can further research?
-RR