Midea top load washer getting an error code? Need help troubleshooting your washing machine? Below we have the common error codes for Midea top load washers. There are multiple Midea top load washers with different model numbers, so be sure to check your model number. Most error codes on Midea top load washers are the same. Some top loading Midea washers will have different error codes and different troubleshooting methods. If you need error codes for Midea front load washers you will find it here.
Midea Top Loading Washing Machine Troubleshooting and Error Codes
We also have the operation panel identification chart and what the buttons functions are and a washer parts identification chart.
Use the error code and troubleshooting guide below to assist you in repairing your broken Midea top load washer.
MIDEA top load washer error codes chart
Midea Top Load Washer Error Code: F0
ERROR CODE SOLUTION: Turn off power, wait 5 minutes, turn on power and start washer again.
Midea Top Load Washer Error Code: F2
ERROR CODE DEFINITION: EEPROM fail.
ERROR CODE SOLUTION: It needs a Repair. Replace Control Board.
Midea Top Load Washer Error Code: E1
ERROR CODE DEFINITION: Not enough water pressure.
ERROR CODE SOLUTION: Make sure to turn on water tap, or increase water flow to washer.
Midea Top Load Washer Error Code: E2
ERROR CODE DEFINITION: Draining not finished correctly.
ERROR CODE SOLUTION: Check drain hose, and clear if required.
Midea Top Load Washer Error Code: E3
ERROR CODE DEFINITION: Lid not closed.
ERROR CODE SOLUTION: Close lid before it begins to spin.
Midea Top Load Washer Error Code: E4
ERROR CODE DEFINITION: Clothing load is out of balance.
ERROR CODE SOLUTION: Move clothes around in drum to balance the machine.
Midea Top Load Washer Error Code: F8
ERROR CODE DEFINITION: Water level sensor failed.
ERROR CODE SOLUTION: Remove and replace water level sensor.
Midea Top Load Washer Error Code: HU
ERROR CODE DEFINITION: Power Voltage Protection error.
ERROR CODE SOLUTION: Check power incoming to washer.
MIDEA top load washer faults and troubleshooting
List of faults and inspection (Midea top load washer):
MIDEA Top Loading Washing Machine PROBLEM: No water flows in
REPAIR or CHECK: If the power is off or the fuse is burned out.
If the water supply is cut off or the water pressure is too low.
If the inlet hose is properly connected and the water tap is opened.
If the filtering screen of inlet valve is blocked by dirt.
If the coil of inlet valve is damaged. (The slight electromagnetic sound is normal phenomenon when the inlet valve is switched on)
If the “Start / Pause” button is pressed after the power switch is pressed.
MIDEA Top Loading Washing Machine PROBLEM: Washer will not wash
REPAIR or CHECK: If the power is off or the fuse is burned out.
If the power supply voltage is too low.
If the water amount reaches to the required water level. (The washer will not work if the water amount does not reach the required water level)
If it is set to “Delay” washing mode. (It will only start to work until the reservation time reached)
MIDEA Top Loading Washing Machine PROBLEM: Washer will not drain
REPAIR or CHECK: If the water drain hose is placed very high.
If the end of water drain hose is sealed in pond.
If the internal rubber ring of drain valve is blocked by dirt.
MIDEA Top Loading Washing Machine PROBLEM: Abnormal spinning
REPAIR or CHECK: If the door lid is closed.
If all clothing piled largely at one side of barrel or the clothing is excessively placed.
If the washer is not placed in stable condition or it is placed in inclination state. (The ground is not flat).
If the motor belt is loose.
IMPORTANT: During the spin process, if clothing is piled up at one side of the spin barrel, it will cause unbalance of spin barrel resulting in striking. At this moment, the computer inside the washer will feel this unbalance phenomenon and will automatically correct it (fill in water Washing). However, if unbalance situation is not removed after continuous three corrections, which means the computer auto-correction can not resolve the problem. Then the user has to manually and evenly place the clothing inside the barrel to solve the problem.
MIDEA top load washer parts identification
MIDEA top load washing machine panel operation
Need the users manual for your Midea top load washer? See below.
Midea 700 Top Load Washing Machine User Manual in PDF
If you have questions about your top loading Midea MT700W washing machine, please leave a comment below and we will be happy to assist.
Written by Keith Schneerer
Certified Appliance Tech · Founder, RemoveAndReplace.com
Keith has spent 30+ years repairing machines, starting as a military mechanic and later maintaining food processing equipment before moving into appliance repair. He founded RemoveAndReplace.com to share field-tested repair advice.
More about Keith →
The washer is constantly on drain mode, as soon as we set to wash and the water comes in the drum, the water just automatically drains. How do we fix it?
Unplug the washing machine before working on it. Did you clean the side lint filter? Did you remove the water pump and check it for broken parts and clogs. The back and bottom come off easy. There is a one screw bottom drain.
Remove the hoses with a pair of channel locks by pinching the clamp tips together and twisting. The drain hose comes off easily. Slowly tilt the machine to let the water drain out.
Error code E2 keeps coming up. I have cleared the drainage pipe. Still same issue. How do I clean or check the drain pump?
when i start my washer the screen turns on after few seconds it goes off
No water flows. Error program
Everything is fine.
How can I Reboot the panel from the previous setting and e2 code?
I left it unplugged overnight with no change. Is there a secret reset button?
I have a E2 Code and it will not clear. I have unplugged overnight and it remains stuck in the same settings with code as when it appeared and stopped washing. I did move the washer when it was running but I don’t know where it was in the cycle. I have taken the wet laundry out and water. I removed the hose and it’s clear. I don’t think there’s a mechanical issue at this point if I could clear the panel