Home » Home DIY Repair » Washing Machine Repair » 7 Steps To Fix Your Whirlpool Washer Not Filling With Water

7 Steps To Fix Your Whirlpool Washer Not Filling With Water

Here are 7 steps to fix your Whirlpool washer not filling with water. Read our repair guide below and you can fix the washer without calling a technician. These 7 proven repair methods are written to help you to fix your Whirlpool washing machine that is not filling with water so you can run a load of laundry.

Whirlpool washer not getting waterWhirlpool washer not getting water

Issue Solution
Clogged Washer Water Filters Clean or replace filters
Bent or Clogged Water Hoses Straighten hoses, check for clogs
Faulty Water Level Pressure Switch Test and replace if necessary
Improperly Set or Faulty Water Inlet Valve Adjust setting or replace valve
Low Water Pressure or Plumbing Issues Check household water pressure and plumbing

Why No Water To Washer?

1. Washer Filters

A common cause for a Whirlpool washer not filling with water is a clogged water filter. Over time, these filters can accumulate debris, restricting water flow.


  1. Locate the water filters on your washer. Refer to the user manual if necessary.
  2. Inspect the filters for any visible debris or blockage.
  3. Clean the filters thoroughly. If they are extensively clogged, consider replacing them.

Pro Tip: Regularly check and clean your washer’s water filters every few months to prevent clogs and maintain optimal performance.

2. Water Hoses Issues

Bent or clogged water hoses can also prevent your washer from filling properly.

Step by Step Guide:

  1. Inspect both hot and cold water hoses for any bends or kinks.
  2. Check the hoses for clogs or buildup of hard water deposits.
  3. Straighten out any bends and clean the inside of the hoses if necessary.

For detailed guidance with long fill error codes, check out our comprehensive guide on Whirlpool Washer Error Code LF.

3. Water Level Pressure Switch Issues

The water level pressure switch can go bad, leading to filling issues.

Step by Step Guide:

  1. Locate the pressure switch. Consult your washer’s manual for its exact location.
  2. Test the switch using a multimeter. If it’s faulty, it will need to be replaced.
  3. Replace the switch if necessary, ensuring it’s properly connected and set.

4. Water Inlet Valve Problems

An improperly set or faulty water inlet valve is a common issue.

Step-by-Step Guidance:

  1. Access the water inlet valve, usually found at the back of the washer.
  2. Check the valve for any blockages and clean as needed.
  3. Test the valve with a multimeter. If it shows no continuity, it needs replacing.

Read more about troubleshooting the washer in our detailed article Whirlpool Washer Error Codes and Fixes.

5. Low Water Pressure or Plumbing Issues

The issue can be outside the washer, such as low water pressure or plumbing problems.

Step-by-Step Guide:

  1. Check the water pressure in your home to ensure it meets the washer’s requirements.
  2. Inspect the plumbing for any issues that could affect water flow to your washer.

6. Plumbing and Water Pressure Checks

In some cases, the issue with your Whirlpool washer not filling with water might be due to external plumbing and water pressure problems.


  1. Inspect Your Home’s Plumbing: Check for any visible signs of plumbing issues that could be affecting water flow to your washer.
  2. Test Water Pressure: Ensure that your home’s water pressure is sufficient for your washer’s needs.

Pro Tip: Regularly monitoring your home’s water pressure can help you identify and resolve issues before they affect your appliances.

7. Checking Electrical Connections

Electrical issues can sometimes cause problems with the filling mechanism of your washer.


  1. Safety First: Always unplug your washer before checking any electrical components.
  2. Inspect Wiring: Look for any loose or damaged wires that could be affecting the washer’s operation.

Preventative Maintenance

Regular maintenance can prevent issues with your Whirlpool washer not filling with water.

Step-by-Step Guide:

  1. Regularly Check Hoses and Filters: This simple step can prevent many common problems.
  2. Schedule Annual Inspections: Have a professional check your washer to ensure it’s in top condition.

Chart - Whirlpool washer not filling with waterChart – shows the most likely reason Whirlpool washer not filling with water

Fix Whirlpool washer that has no water

A Whirlpool washer that is not filling with water involves checking components like water filters, hoses, pressure switches, valves, and even your home’s plumbing and electrical systems. If you check all the items on this page, you will be able to fix it yourself.

If you still have problems after reading this article, please feel free to add a comment below that describes your problem with your Whirlpool washer. For more information and extra help please provide your Whirlpool washer model number.

Leave a Reply

Leave a Comment

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.