Dryer not heating or drying your clothing? If your dryer is all of a sudden not drying your clothes, then we have a few simple DIY fix tips you can try yourself. If the dryer is no longer drying your clothes then the first thing to do is to check and clean the dryer lint filter trap.
How To Fix A Clothes Dryer That Is Not Drying
Check Dryer Lint Filter
We were forced to add that as our first step as there really are some people who do not realize there is a LINT FILTER that must be cleaned before or after each use. Once that is cleaned out, check if the dryer is still NOT drying your clothes.
Check Vent Hose On Back Of Dryer
If that was NOT the cause of the problem, then you will need to inspect the vent hose on the back of the dryer. Commonly this HOT AIR VENT HOSE will become clogged, caked or full of lint that is constantly being removed from your clothing when drying. When this happens your dryer is unable to expel the hot air from within, therefore making it impossible for your dryer to actually dry your clothing in a timely manner or at all.
Common Causes For Dryer To Stop Heating
- The dryer lint screen (lint trap) has not been cleaned (poor or restricted airflow).
- A clogged or kinked (bent) dryer air vent hose (inadequate or no airflow).
- Drum has stopped turning, broken drum drive belt.
- Overheated or bad motor (possible thermal overload).
- Thermal fuse or thermostat (could be caused from dryer air vent hose lint buildup)
- Heating element burnt out.
- Loose electrical plug or power socket.
- Other mechanical issue, fault or malfunction.
Click here for a faster way to troubleshoot your dryer not heating
Clothing Takes Forever To Dry
If your clothes dryer is taking forever to dry your clothes or it is not drying your clothing at all (and you already thoroughly cleaned the lint filter screen), then the first step is to CLEAN OUT THE INSIDE OF THE DRYER VENT HOSE.
First, unplug your dryer from the electrical socket on the wall. Slide the dryer forward very carefully so you can get behind it. Locate the (usually silver colored) air vent hose, and remove it from the wall and the dryer (2 connection points).
Do this by squeezing the clip at both ends and pulling the hose outward. Using a long dryer vent brush or similar, clean out the inside of the air vent hose by removing all of the built up lint and dust looking material.
Clean the area on the back of the dryer and the hole in the wall where the air is vented out. Most of the time the lint will be built up in both of these areas.
Once all of the lint is cleaned out, reattach the vent hose and slide the dryer back in place. Make sure you DO NOT KINK the vent hose when repositioning the dryer as this will cause the dryer to NOT expel the hot air properly.
If you kink the hose the dryer will not function properly and your clothes will take forever to dry. Next, plug the dryer back into the power outlet and run a test. If your dryer is now heating and properly drying your clothes then you fixed the problem. If not, read on…
If you know what Dryer Replacement Parts you need, here is where to get them at a GREAT PRICE and most have FREE shipping.
Here is how much lint that can become stuck in your dryer vent hose.
This much lint in the hose or in the wall, will prevent your dryer from properly drying your clothes.
DO NOT LET THIS HAPPEN! Dryer air vent hose clogged with lint.
Clean your dryer AIR VENTING HOSE on a yearly basis!
It is the reason your dryer takes forever to dry AND can be a fire safety hazard!
Dryer Has Overheated
At times your dryer can overheat and this can cause the motor that turns the drum to stop working temporarily. There is a safety mechanism built into the motor that makes it stop working if it gets too hot. This is called a thermally protected motor.
Your dryer may seem to be running but the motor will not be turning the drum. If the drum is not turning then the clothes are not moving. Therefore they can not get DRY. So if your dryer motor is NOT turning on but the rest of the dryer works, such as the lights and other mechanical parts, then your motor is probably overheated.
For this, you need to just give the motor some time to cool down. If you suspect that this is your problem then give the dryer about an hour to cool down and run a test after that. If your motor has overheated then you may be overloading your dryer with too many clothes. Try running the dryer with less clothes in it the next time you dry a load and this should remedy the issue.
The solutions above are the most common causes for this specific malfunction. If the explanations above have not been your specific problem, then there can be a number of things wrong. If you feel comfortable you can remove the front panel of your dryer (while unplugged) and look to see if there are any obvious causes of the problem.
A possible loose wire, loose part, burnt area, pieces of the dryer that have come off, fried or burned mechanical switches, etc. If the problem is not visual and you do not know what the issue can be, we recommend going here and posting an appliance repair question to online appliance repair technicians. If all else fails then simply leave a comment or question below and we PROMISE to answer your question in a timely manner.
Other components that could be at fault would be the Thermal fuse, Thermal cutoff, Heating element, Operating thermostat, and High limit thermostat. You can check all of these for continuity with a multimeter. If any are determined bad, remove and replace.
How Does It Work? Basic Clothes Dryer Function
Dryer Parts Schematic Parts Location Diagram Chart
If you still need help, assistance, or answers to fix your Dryer Not Heating problem, ask your
questions over at our Appliance Repair Help page for free answers to fix your broken appliance!
Bill,
Dryer most likely has 2 thermostats. One is probably bad. Do you have a model number so we can research further?
-RR
I have a whirlpool dryer it gets hot and turns but clothes are still damp after a 120 min drying cycle. ive cleaned it and checked the vents still the same problem checked therm. on heater box with a meter and the coil all is good so what can it be.
I found out the problem with mine! Posting here so others may benefit from it.
I ordered new dryer and old one was hauled away. My new dryer didn’t heat up too!
The problem was not with the dryer but the electric wire….The voltages were not enough to heat up the element!
I figured this out when old one with absolutely no problem was gone!
Make sure you check for this :)
Thanks
Sarah
Stephan,
Be sure lint catch filter is clean. If lint screen and vent hose are clean and NOT blocked, then the issue probably is within your dryer. Are you sure your dryer is on the highest heat setting? If everything is as it should be, the first part to check is the thermal fuse on back. If the thermal fuse goes bad, the dryer will spin but will NOT provide any heat. The other parts that could be bad are the coils or thermostats.
-RR
My dryer is not drying clothes. I checked the dryer vent and hose and it is not clogged with lint. What else could be the issue?
RB,
We would suggest unplugging dryer, removing service panel, and visually inspect inside. You may see something burned or broken. If not you will have to test each component with a multimeter to determine which part is the faulty one.
-RR
I have a 5yo Front Loading Samsung DV328AEE/XAA and it has stopped heating. I have cleaned all lint related areas, help the button and tumbler has spun for more than 5 minutes with no heat. Research has shown me that it could be the coil, the thermostat or heating element. Is there a way that I can tell witch is the sulprit without ordering all 3 parts?
Please help.
Thank You
RB
Sarah,
Why did the technician not fully troubleshoot your dryer problem?
You need to test the timer in ohms. This will tell you if a particular part of the timer is bad. Set your ohmmeter to the Rx1 setting. A normal reading for a dryer timer is in the 2000 – 3000 ohms range. You should find the schematic for your dryer to find out any info that applies to your particular dryer. The schematic should tell you the proper resistance reading for your specific dryer timer motor. If the reading you get from testing your dryer timer’s motor is completely off from the 2000 – 3000 ohms range then replace the dryer timer motor. Replace just the motor itself and not the entire assembly as this will save you money.
-RR
Technician checked fuse and elements. To verify whether timer is a problem, I checked continuity in red and black wires of the timer. It doesn’t show continuity. Does this mean timer needs replacement? or there is easy/cheap way to fix it?
Thanks,
Sarah
Claudia,
Make sure lint filter clean. Make sure dryer is on high heat. Be sure the vent hose is clear. Check to see if another setting is set incorrectly. Possibly test thermostats with a multimeter.
-RR