Here is information that will assist you in identifying what may be making your GE washer display an error code. Identifying what the error or fault code is will help you to repair your washer. The GE specific error fault codes below are to give you an idea as to what part is at fault. You may have to do further troubleshooting to find what may be causing the fault for that specific part.
GE Washing Machine Error/Fault Codes – Probable Fault Identifiers
GE WSL Model Washer Error Codes
IE
Water level sensor error
7E
Water supply error
E
Drain pump error
dE
Lid open error
UE
Unbalance switch error
OE
Water overflow error
GE Front load Washer Error Codes
E22
Fill timeout: No fill or slow fill
E23
Flood protect drain Foam switch closes in idle state
E30
Drain pump not present Drain problems
E31
Drain timeout: Slow drain
E38
Dispenser error
E39
Dispenser timeout
E42
Drive motor: Instantaneous current Motor excess current draw
E43
DC Fault–Inverter failure: Replace inverter control board
E45
Drive motor: Overload current Load too heavy
E46
Drive motor: Over temperature, Inverter over temperature
E47
Heat sink: Over temperature, Inverter over temperature
E48
Drive motor: Open motor phase
E49
Drive motor: Overload power
E4A
Under volts: DC bus voltage (inverter)
E4B
Power up problems is Software/hardware problems
E4C
Over volts: DC bus (inverter)
E4E
Under volts after start Initial minimum voltage not received: Motor does not run
E52
Main control wake-up error Lost communication between control and drive motor
E53
Buffer error Internal software buffer error
E54
No motor response: Lost communication between control and drive motor
E57
Checksum failure Software error occurs
E58
Communication failure: Non-recoverable error
E60
Door lock switch failure
E61
Door unlock switch failure
E62
System contact failure: Heater/pump/pressure switch/door lock
E63
Unexpected open door
E64
Unexpected open door while running
E65
Water level sensor failure
E66
Water temperature sensor open
E67
Water temperature sensor shorted
E70
Stuck key Continuous key read for 60 seconds
E71
Key fault Communication error between control and keys
If your GE Washing Machine Error Code is not listed here, check
Google or YouTube to find the exact error code your GE is displaying.
Here are error codes for Amana, Asko, Beko, Bosch, Daewoo, Fisher & Paykel, Frigidaire,
GE, Haier, Hotpoint, Kenmore, LG, Maytag, Samsung, and Whirlpool washers.
Here are Washing Machine Error Codes For All Washing Machines.
Need assistance with finding an error code for your washer?
Ask your question below and we will be happy to assist.
Sheila,
The FH error code on your GE front loading washer indicates that there is a water supply issue.
This could be caused by a few different things, including a clogged filter or inlet valve, low water pressure, or a kinked water supply line.
The washer is stopping because there is a water supply problem.
Check that the washer is getting water, check the water valve on the wall to be sure it is fully open, check the water hoses as they could be clogged or bent, then check the water valve where the water goes into the washer.
Let us know what you find out to fix the problem.
-RR
I have a GE front loading washer. It fills with water and starts. After going around about 3 or 4 times it will start humming then shut off giving me a code f h then stops. What is the problem?
My GE front load washer wcvh6600hbb cycle knob is stuck on speed cycle. That is the only cycle i can pick but the washer does work on that setting. What can i do to fix this problem? And what parts do you think I am going to need
What sequence is used on the GE front load washer to access the error codes from the machine?
Model 1200.
Lewis,
The Kenmore washer error code LE means a motor error. Most likely the motor is overheating and needs time to cool down therefore you are having to wait to do a wash an hour or so later. You may need to replace the motor. OR… This may be a simple fix as a bolt may have become loose that holds the motor in position. It could also mean the motor is bad or on the fritz. Do some troubleshooting and try to see if the motor is tight, secure and in place. Be sure it is running properly and be sure ALL wire harnesses are tight and not damaged. After this run a test wash and see what you find. Hopefully it was a simple wire harness being loose or a the motor bolts were loose. If not the motor is most likely needing replaced. Let us know what you find.
-RR
my Kenmore washer (model # 796 4027 2900) stopped working and the power light would not come on. I checked breaker, plug, etc . and bought a mother board. Installed and it turned on. Started a wash load and 15 minutes into the load it quit and put an LE code on panel. I followed instructions and let it sit for thirty minutes to cool down. Took some clothing out to lighten load, restarted. After about 3 minutes, it stopped again. Waited an hour next time and took more clothing out. I restarted and it happened again. What is the problem?