Fisher & Paykel Washing Machine is displaying an Error Code? Here is information that will assist you in identifying what may be making your Fisher & Paykel washing machine display an error code. Identifying what the error or fault code is will help you to repair your washer. The Fisher & Paykel AquaSmart error fault codes below are to give you an idea as to what part is at fault. These Fisher & Paykel error codes may not apply to all Fisher & Paykel washers. You may have to do further troubleshooting to find what may be causing the fault for that specific part. For more assistance finding the exact error on your washing machine, please ask a question below.
Fisher & Paykel Aquasmart Top Load Washer Error Codes
Fisher Paykel Top-Load Washer Error Codes = Numbers 21, 26, 27, 49, 50, or 246.
Error Fault Condition – Water Inlet Valve Fault.
Repair or Check – Unplug the washer from power. Reconnect any non secure wires on the water inlet valve. Replace the wire harness if it is found to be damaged. If the wiring is okay then measure the resistance of the water inlet valves using an ohm meter. If the resistance of each water inlet valve solenoid is not 60 to 62 ohms then replace the complete water inlet valve assembly.
Parts for Replacement – Water Inlet Valve Assembly or Wire Harness.
Fisher Paykel Top-Load Washer Error Codes = Numbers 38 or 39.
Error Fault Condition – Water Level Pressure Transducer Air Tube Fault.
Repair or Check – Unplug the washer from power. Reconnect the water level pressure switch air tube. Replace the air tube if it is found to be damaged.
Parts for Replacement – Water Level Pressure Switch Air Tube.
Fisher Paykel Top-Load Washer Error Codes = Numbers 58 or 68.
Error Fault Condition – Water Level Pressure Transducer Fault.
Repair or Check – The water level pressure transducer is in the motor control module. Unplug the washer from power and replace the motor control module.
Parts for Replacement – Motor Control Module.
Fisher Paykel Top-Load Washer Error Codes = Numbers 10, 41, or 237.
Error Fault Condition – Thermistor aka = Water Temperature Sensor Fault.
Repair or Check – Unplug the washing machine from power. Reconnect any unsecured wires in the thermistor circuit. Replace the wire harness if it is found to be damaged. Measure the thermistor resistance using a ohm meter. Replace the thermistor if the resistance is not 12.5K ohms at 68 degrees Fahrenheit.
Parts for Replacement – Thermistor or Wire Harness.
Fisher Paykel Top-Load Washer Error Codes = Numbers 1, 57, 60, 107, 108, 112, 133, 220, 221, 222, 223, 224, 225, 226, 230, 232, 233, 236, 241, 243, 252, or 254.
Error Fault Condition – Motor Control Module Fault.
Repair or Check – Unplug the washer from power. Replace the motor control module.
Parts for Replacement – Motor Control Module.
Fisher Paykel Top-Load Washer Error Codes = Numbers 45, 46, 103, 104, 105, 106, or 241.
Error Fault Condition – Display Module Fault.
Repair or Check – Unplug the washing machine from power. Replace the display module.
Parts for Replacement – Display Module.
Fisher Paykel Top-Load Washer Error Codes = Numbers 234, 235, 238, or 239.
Error Fault Condition – Lid Lock is Bad.
Repair or Check – Unplug the washer and reconnect any loose wires from the lid lock assembly. Replace the wire harness if it is found to be damaged. Measure the resistance of the lid lock using a volt/ohm meter. If the resistance is not 62 to 64 ohms then replace the lid lock assembly. If the resistance is found to be in the correct range then replace the motor control module.
Parts for Replacement – Lid Lock Assembly or Wire Harness or Motor Control Module.
Fisher Paykel Top-Load Washer Error Codes = Numbers 40, 56, or 160.
Error Fault Condition – Spin Basket Will Not Engage Or Disengage From Clutch.
Repair or Check – The spin basket has to be able to rise and fall with the water level. This is to engage and disengage from the clutch. Unplug the washer from power. Remove the spin basket. Remove any objects found between the spin basket and the tub. An object could be interfering with the spin basket clutch engagement. Replace any broken drive components.
Parts for Replacement – Drive Components.
Fisher Paykel Top-Load Washer Error Codes = Numbers 136 or 137.
Error Fault Condition – Motor Is Not Running.
Repair or Check – Unplug the washer from power. Rotate the spin basket by hand. If the spin basket will not rotate freely by hand then remove any objects between the spin basket and tub. If the spin basket rotates freely by hand then replace the drive motor as it is most likely defective. If the problem keeps happening then replace the motor control module.
Parts for Replacement – Drive Motor or Motor Control Module.
Fisher Paykel Top-Load Washer Error Codes = Numbers 37, 114, 245, 247, 248, 249, 250, or 253.
Error Fault Condition – Water Is Not Draining.
Repair or Check – Remove any clogs from homes drain that is used for the washer. Remove any clogs or bends from the washers draining hose. Unplug the washer from power and check the drain pump for a blockage. If the drain pump is defective it will need to be replaced.
Parts for Replacement – Drain Pump.
Fisher & Paykel Aquasmart washing machine error codes list
Fisher and Paykel washer NEW fault codes
Fisher and Paykel washing machine = Diagnostic mode
If your Fisher & Paykel Washing Machine Error Code is not listed here, check
Google or YouTube to find the exact error code your Fisher & Paykel is displaying.
Here are error codes for Amana, Asko, Beko, Bosch, Daewoo, Fisher & Paykel, Frigidaire,
GE, Haier, Hotpoint, Kenmore, LG, Maytag, Samsung, and Whirlpool washers.
Here are Washing Machine Error Codes For All Washing Machines.
NEED Fisher & Paykel WASHER PARTS? New and Discounted
Washing Machine Replacement Parts For ALL Washing Machine Models
Need assistance with finding an error code for your Fisher & Paykel washer? Ask your question below and we will be happy to assist.
Helen,
Is your AquaSmart washer on level ground?
What happens if you run an empty load, does it jump around?
You may have a spring or a tub balancer that has fallen off or is loose.
Check the outer drum to see if that is the case.
-RR
Similar to 3 above. My AquaSmart clothes washer model # WLTOT60DW1 gets very unbalanced in spin cycle. It spins for a little while then machine jumps around the floor, sometimes self correcting then spins again, sometimes beeping but regardless of whether or not I rearrange the clothes it will spin a little then repeats whole process. The clothes are still very wet when I give up and remove them. Any ideas?
David Forsyth,
FISHER AND PAYKEL DRYER ERROR CODE 9: EXHAUST SENSOR UNDER TEMPERATURE
The exhaust sensor measures under temperature (open circuit or not plugged in)
TO FIX ERROR CODE 9:
Check the integrity of the sensor circuit checking particularly for short circuits.
Replace thermistor and harness if out of range.
Check the element integrity in that it switches off when the dryer is stopped.
Replace the motor control module.
Replace the sensor module.
-RR
I have a Dryer. It is a Fisher & Paykel Aerosmart
Model: DG27CW1
S/N: LEU309983
It shows “Error Code 9”
Can you tell me what that error means?
Coral Venn,
Can you supply us with the model number of your Fisher & Paykel Washing machine? This will give us a better idea of what may need to be replaced. What exactly happens to your washer? It goes offline as in it has NO POWER? Or the washer sits in the middle of a cycle and does nothing? Are the lights on the washer still illuminated when this issue happens? Any error codes present?
-RR
FP Aqua smart machine, when machine gets to spin cycle it goes off line. Have tried to even arrange weight evenly to no avail. Have tried to spin empty with just water… still the same. Have leveled the machine still the same. Ready to toss it out the window, have you any suggestions please?
Michael,
Fisher Paykel Error code 9 means the washer needs to be reset to size. To correct error code 9….
1 – Turn the machine off using the Power button.
2 – Hold down the Left Scroll button and press the Start/Pause button. This will bring up a screen for setting the size of the machine.
3 – Use the scroll buttons to choose the appropriate value. Start with the size 650 and if that does not work, try different size settings.
4 – Once you have your size setting, press the Power button to save the setting and exit.
-RR
Have changed the control panel 421232nap on my Fisher & Paykel washer. After it fill with water, I am getting fault code 9. How do I reset it? I’m a retired TV tech and this was only problem I found. Many thanks in advance!
Betsy,
It should take only a few minutes under normal circumstances. The installation test cycle just checks to see if there are any errors or faults in the system. If it is taking a long time, are there any error codes displayed?
Fisher & Paykel Washing Machine Installation test cycle…
Your washer must be correctly installed before use. Check the machine’s installation and operation using the following procedure:
1 – Touch POWER to activate your washer.
2 – Touch both the KEYLOCK and OPTIONS buttons at the same time, and hold for three seconds.
3 – Touch START/PAUSE to start the installation test cycle.
4 – The machine will beep to signal the end of the installation test cycle. Any faults will be displayed on the screen.
Note: if there are no faults found, the washer will automatically turn off at the end of the installation test cycle.
-RR
How long does installation test cycle last?