Is your Samsung Top Load Washer WA5471 or WA5451 not spinning, not starting, leaking, getting error codes, not draining, flashing, wrong temp, not filling?
We have all the ways to troubleshoot your Samsung top load washer here. Remember, if you have any questions about repairing your Samsung top load washer, please leave a comment below describing your issue and we will be happy to assist troubleshooting.
Samsung top load washer troubleshooting
Below are many different troubleshooting diagrams, electrical schematics, water flow diagrams, eeprom check, board input test modes, continuous run mode, fast time down test mode, service modes, error codes, diagnostic test check modes and more. These are meant for troubleshooting on the SAMSUNG TOP LOAD WASHER WITH MODEL NUMBERS WA5471 or WA5451 ONLY.
Samsung top load washer WA5471 WA5451 troubleshooting
Once you find the issue with your Samsung Top Load Washer
we can help you find the replacement parts you need for less!
Samsung top load washers replacement parts
___________________________________________________________
Board input test mode
___________________________________________________________
Continuous run mode
___________________________________________________________
Cycle count check mode
___________________________________________________________
Diagnostic code check mode
___________________________________________________________
eeprom clear check for Samsung top load washers
___________________________________________________________
Fast time down test mode
___________________________________________________________
Problem checking of PCB
___________________________________________________________
Samsung service mode
___________________________________________________________
Samsung top load quick test mode
___________________________________________________________
Samsung top load washer error codes 1
___________________________________________________________
Samsung top load washer dc error, unbalanced, fix
___________________________________________________________
Samsung top load washer error codes 2
___________________________________________________________
Samsung troubleshooting no water fill, will not lock, will not unlock
___________________________________________________________
Samsung troubleshooting wont drain, noisy, wrong water temp, buttons do not respond
___________________________________________________________
Samsung wring diagram schematic WA5471 WA5451
___________________________________________________________
Troubleshooting wont spin, leaking, will not start – Samsung washer
___________________________________________________________
Water flow diagram Samsung top load washer
___________________________________________________________
Samsung WA5451 Top-load Washer In Action
___________________________________________________________
How High Efficiency HE Top Load Washers Work
Here are error codes for Amana, Asko, Beko, Bosch, Daewoo, Frigidaire, GE,
Haier, Hotpoint, Kenmore, LG, Maytag, Samsung, and Whirlpool washers.
Here are Washing Machine Error Codes For All Washing Machines.
Do you have suggestions or questions about your Samsung Top Load Washer? Please leave a comment below.
Written by Keith Schneerer
Certified Appliance Tech · Founder, RemoveAndReplace.com
Keith has spent 30+ years repairing machines, starting as a military mechanic and later maintaining food processing equipment before moving into appliance repair. He founded RemoveAndReplace.com to share field-tested repair advice.
More about Keith →
Cody,
Can you give us the exact model number of your washing machine? We can troubleshoot from there.
-RR
My Samsung top load has started to spin out of control. It stops the spin cycle and fills up with water again. Will do this 3-4 times till it actually finishes. When it spins out of control it really sounds like I put a brick in with the clothes. And ideas?
Samsung WA 5471 water leaks profusely from bottom during the fill cycle. Turned washer up, drain hose was completely disconnected. Replaced it but it is still leaking. There doesn’t seem to be any visible damage to hoses or connectors. I would appreciate any advice you could offer. Thank you!
Karineh G.,
Checking the drain pump on your Samsung top load washer will involve, unplugging the washer, removing the back panel, and finding the drain pump. There will be hoses connected to the drain pump that will need to come off to inspect the drain pump itself and the hoses for blockage. It will be fairly easy, you just need to slide the washer out to gain access to the back. Turn off water and remove hoses and drain line. See a few videos on YouTube if needed on how to gain access into your Samsung washer.
-RR
Thank you so much for your prompt response. We have already checked the drain hose for blockage and didn’t find any. We let it drain into the laundry sink instead of wall drain to rule out any blockage there and we still saw the problem. We haven’t checked the drain pump though. Is it a fairly easy task? Could you please provide some tips on how to do that?
Karineh G.,
The ND error code means NO DRAIN. This indicates a blockage somewhere or a part may have gone bad. First, check to be sure the drain hose is not bent, blocked, or crimped. Take the hose off and be sure there is no blockage whatsoever. Check to be sure where the drain hose goes into the wall drain that it is not blocked up. If the drain hose and the wall drain is okay, then check the drain pump itself as it may have some objects in it that may be causing a blockage. If there is no blockage in the draining system, then you may have a bad or malfunctioning drain pump. Check power and wire harnesses to the drain pump to be sure it is receiving power and operating as normal.
-RR
Our washer started displaying the ND error code towards the end of wash cycle a couple of weeks ago. We drained the water bucket by bucket and started on rinse and spin setting without any clothes and it ran OK. We thought it may have been a fluke but it came back after a couple of error free washes and now it happens all the time. Sometimes it just gets stuck and won’t do anything. We have checked the hose and the tip of the area where it connects to the machine but didn’t see any obstructions. Before calling a service person, is there anything else we can try?