Here is information that will assist you in identifying what may be making your Bosch washer display an error code. Identifying what the error or fault code is will help you to repair your washer. The Bosch specific error fault codes below are to give you an idea as to what part is at fault. You may have to do further troubleshooting to find what may be causing the fault for that specific part.
BOSCH Washing Machine Error/Fault Codes – Probable Fault Identifiers
Bosch Logixx WAS Series Washing Machine Error Codes
F16
Door lock error
F17
Inlet valve error detected
F18
Drain error detected
F23
Anti flood device has been activated
F34
Door lock error
F42
Motor fault
F43
Motor fault
F44
Motor fault
Bosch WAE Range Washing Machine Fault Codes
F16
Door lock problem
F17
Inlet valve
F18
Drain pump
F21
Motor
F23
Anti flood system activated
Bosch WFP Range Washing Machine Fault Codes
F01
Water intake timeout
F02
Heating timeout
F03
Draining timeout
F04
Motor fault
F05
Uncontrolled motor startup
F06
Short on NTC Detected on hot water intake
F07
Open circuit NTC Open circuit wiring
F08
Door open when program started
F09
Unexpected heating
F10
Communication error
F11
Overheating
F12
Short circuit
F13
Mains voltage too high
F14
Mains voltage too low
F15
Faulty temperature sensor on motor PCB
F16
Faulty rinse sensor Displayed only in test
If your Bosch Washing Machine Error Code is not listed here, check
Google or YouTube to find the exact error code your Bosch is displaying.
Here are error codes for Amana, Asko, Beko, Bosch, Daewoo, Fisher & Paykel, Frigidaire,
GE, Haier, Hotpoint, Kenmore, LG, Maytag, Samsung, and Whirlpool washers.
Here are Washing Machine Error Codes For All Washing Machines.
Need assistance with finding an error code for your washer?
Ask your question below and we will be happy to assist.
Written by Keith Schneerer
Certified Appliance Tech · Founder, RemoveAndReplace.com
Keith has spent 30+ years repairing machines, starting as a military mechanic and later maintaining food processing equipment before moving into appliance repair. He founded RemoveAndReplace.com to share field-tested repair advice.
More about Keith →
Joe M,
If your washer was working properly before replacing the bearing, you may have inadvertently disconnected a wire harness on the motor or on the control board when you had the washer apart. Retrace all wire harnesses and find one that is most likely loose. If that is not the issue let us know and we can assist from there.
-RR
I have a Bosch nexxt 300 series washer. The bearing went out and the tub stopped. I had a repair friend help me replace the rear tub and bearing and it worked except it skips the spin cycle.
I went through the error codes and found 1 for the door being open that was me.
And P:03 d:08. Motor sensor fail.
Does this mean that my motor is bad?
Is there a way to reset the machine like most things?
Is there a button or breaker that I can switch?
Chris,
The error code of F34 on your Bosch washing machine is a door lock fault. Remove and replace the door lock assembly.
The Bosch washing machine manual says this…
Door lock is broken SAFETY ERROR – switch ON/OFF for reset Normal mode
Door hook is stuck – washing program is aborted – check door lock
Door is stuck – door is unlocked, if possible – check mechanism
Stiff gasket – operator control actions are blocked – check wire harness
-RR
I have a Bosch Axxis + Washer WAS24460 UC with error code F:34. The door mechanism is making noise and locking then unlocking constantly until the error message pops up. How can I reset?
I have a similar problem & can’t reset my Logixx8 washing machine. Is there an easy way to reset or does it need to be looked at as E:23 error is not going away ? Cheers , Mark
We have been getting an 01 error message indicating a water intake problem. We disconnected the hoses, checked/cleaned the screen caps and reconnected them. Looks like the error occurs during the rinse and spin cycles. Suggestions? Thanks.
Greg,
Bosch washer error code E13 indicates that your pump is taking too long to empty. The drain filter and pump needs cleaned out. Check, clean, and run a test cycle.
-RR