Frigidaire Affinity Front Load Washing Machine Error Fault Codes. Here is information that will assist you in identifying what may be making your Frigidaire affinity front load washer display an error code. Identifying what the error or fault code is will help you to repair your washer. The Frigidaire specific error fault codes below are to give you an idea as to what part is at fault. You may have to do further troubleshooting to find what may be causing the fault for that specific part.
FRIGIDAIRE Washing Machine Error/Fault Codes – Probable Fault Identifiers
Frigidaire Affinity Front Load Washer Error Codes 1
Frigidaire Washer Error Code Chart 2
Frigidaire Washer Error Code Chart Test 1
Frigidaire Washer Error Code Chart Test 2
Frigidaire Front Load Washer Error Codes
E11
Fill time too long
CHECK: Water inlet valve assembly
E13
Water leak in tub or air leak in air bell
CHECK: Outer wash tub, Air hose, Water-level pressure switch
E21
Water not pumping out fast enough
CHECK: Drain Pump
E23
Drain pump relay on control board failed or wire off pump
CHECK: Electronic control board
E24
Drain pump relay on control board failed or wire off pump
CHECK: Electronic control board
E31
Pressure sensor not communicating with control board
CHECK: Water level pressure sensor
E35
Pressure sensor indicates water overfill
CHECK: Water-level pressure sensor, Water inlet valve assembly
E36
Control board problem
E41
Control board thinks the door switch is open
E43
Control board problem
E44
Control board problem
E45
Control board problem
E46
Control board problem
E47
Board thinks the door PTC circuit is open in spin
CHECK: Door lock/switch assembly, Wiring harness
E48
Board thinks the door PTC circuit is closed
CHECK: Door lock/switch assembly, Wiring harness
E52
Bad signal from generator
CHECK: Drive motor, Speed control board
E56
High motor current
CHECK: Drive motor, Outer tub, Spin basket, Speed control board
E57
High current on motor phase
CHECK: Drive motor, Outer tub, Spin basket, Speed control board
E59
No signal for 3 seconds
CHECK: Drive motor, Outer tub, Spin basket, Speed control board
E5A
High temp on heat sink caused by overloading
E5B
High temp on heat sink
E5C
High temp on heat sink
E5D
Communication problem
E5E
Communication problem
E5F
Communication problem
E66
Heating element relay failure
E67
Input voltage on microprocessor incorrect
E68
Current leakage to ground on heater or fuse opened
E70
The control board is not seeing the correct water supply
E71
Wash NTC failure
E74
Wash temperature does not increase
E75
Water temperature sensor circuit
E76
NTC temperature for the cold water valve over the limits
E82
Console control problem
E83
Console control problem
E91
Communication error between UI board and control board
E93
Console control problem
E94
Console control problem
E95
Communication error
E97
Console control problem
E98
Console control problem
EB1
Incoming power frequency out of limits
EB2
Incoming line voltage above 130 VAC
EB3
Incoming line voltage below 90 VAC
EF1
Clogged drain pump
EF2
Too much soap
EBE
Console control problem
EBF
Console control problem
EF5
NTC temperature for the hot water valve over the limits
If your Frigidaire Washing Machine Error Code is not listed here, check
Google or YouTube to find the exact error code your Frigidaire washer is displaying.
Here are error codes for Amana, Asko, Beko, Bosch, Daewoo, Fisher & Paykel, Frigidaire,
GE, Haier, Hotpoint, Kenmore, LG, Maytag, Samsung, and Whirlpool washers.
Here are Washing Machine Error Codes For All Washing Machines.
Need assistance with finding an error code for your washer?
Ask your question below and we will be happy to assist.
My frigidaire front load is washing for five minutes and then all the lights go out and unable to restart then e91 is displayed. I tried to reset by unplugging for 30 minutes but no success
Getting e 99 on my washer after replacing motor control. Please help
My model number is fafw3921nw0, and I’m receiving the same error code E32. It won’t add water, or spin. And I only received the code when I held the Start/Pause, and Cancel buttons for it to show me the code. According to the chart above, this code doesn’t even exist
Electrolux Frigidaire Refrigerator Affinity Model LTF6000FSO – year 05/07
When it powers on, it says ERR and no error codes.
Won’t go into diagnostic mode and wont show any error codes.
Just keeps saying ERR.
Sometimes it will scroll through the adjust temp settings when you press the start button, other times it just shows ERR and all Adjust temp settings flash on and off.
I’ve reset it at the circuit breaker and the same issue keeps happening.