Frigidaire Affinity Front Load Washing Machine Error Fault Codes. Here is information that will assist you in identifying what may be making your Frigidaire affinity front load washer display an error code. Identifying what the error or fault code is will help you to repair your washer. The Frigidaire specific error fault codes below are to give you an idea as to what part is at fault. You may have to do further troubleshooting to find what may be causing the fault for that specific part.
FRIGIDAIRE Washing Machine Error/Fault Codes – Probable Fault Identifiers
Frigidaire Affinity Front Load Washer Error Codes 1
Frigidaire Washer Error Code Chart 2
Frigidaire Washer Error Code Chart Test 1
Frigidaire Washer Error Code Chart Test 2
Frigidaire Front Load Washer Error Codes
E11
Fill time too long
CHECK: Water inlet valve assembly
E13
Water leak in tub or air leak in air bell
CHECK: Outer wash tub, Air hose, Water-level pressure switch
E21
Water not pumping out fast enough
CHECK: Drain Pump
E23
Drain pump relay on control board failed or wire off pump
CHECK: Electronic control board
E24
Drain pump relay on control board failed or wire off pump
CHECK: Electronic control board
E31
Pressure sensor not communicating with control board
CHECK: Water level pressure sensor
E35
Pressure sensor indicates water overfill
CHECK: Water-level pressure sensor, Water inlet valve assembly
E36
Control board problem
E41
Control board thinks the door switch is open
E43
Control board problem
E44
Control board problem
E45
Control board problem
E46
Control board problem
E47
Board thinks the door PTC circuit is open in spin
CHECK: Door lock/switch assembly, Wiring harness
E48
Board thinks the door PTC circuit is closed
CHECK: Door lock/switch assembly, Wiring harness
E52
Bad signal from generator
CHECK: Drive motor, Speed control board
E56
High motor current
CHECK: Drive motor, Outer tub, Spin basket, Speed control board
E57
High current on motor phase
CHECK: Drive motor, Outer tub, Spin basket, Speed control board
E59
No signal for 3 seconds
CHECK: Drive motor, Outer tub, Spin basket, Speed control board
E5A
High temp on heat sink caused by overloading
E5B
High temp on heat sink
E5C
High temp on heat sink
E5D
Communication problem
E5E
Communication problem
E5F
Communication problem
E66
Heating element relay failure
E67
Input voltage on microprocessor incorrect
E68
Current leakage to ground on heater or fuse opened
E70
The control board is not seeing the correct water supply
E71
Wash NTC failure
E74
Wash temperature does not increase
E75
Water temperature sensor circuit
E76
NTC temperature for the cold water valve over the limits
E82
Console control problem
E83
Console control problem
E91
Communication error between UI board and control board
E93
Console control problem
E94
Console control problem
E95
Communication error
E97
Console control problem
E98
Console control problem
EB1
Incoming power frequency out of limits
EB2
Incoming line voltage above 130 VAC
EB3
Incoming line voltage below 90 VAC
EF1
Clogged drain pump
EF2
Too much soap
EBE
Console control problem
EBF
Console control problem
EF5
NTC temperature for the hot water valve over the limits
If your Frigidaire Washing Machine Error Code is not listed here, check
Google or YouTube to find the exact error code your Frigidaire washer is displaying.
Here are error codes for Amana, Asko, Beko, Bosch, Daewoo, Fisher & Paykel, Frigidaire,
GE, Haier, Hotpoint, Kenmore, LG, Maytag, Samsung, and Whirlpool washers.
Here are Washing Machine Error Codes For All Washing Machines.
Need assistance with finding an error code for your washer?
Ask your question below and we will be happy to assist.
I have a frigidaire affinity and I cant seem to figure out what is wrongi get no error codes just Err I have tried to reset, i have unplugged and i even unplugged the connections to the door mechanism and I still get same results any help would be great thanks
Have A Frigidaire Mod LTF2940eSo purchased 06/05
Have Error code E61 this code is not in my tech data sheet
What does it tell you ?
I’ve replaced the motor control board on the Frigidaire affinity washer, and now is giving me E99. I can’t find what is E99 error code is. Do anyone know how to fix this code?
Washing machine won’t final spin in normal cycle mode so clothes are dripping and water in bottom.
I run spin to drain and it works and then re spin out the clothes in small batches after wringing out first.
The quick cycle usually works.
My latch broke and replaced.
No error codes.
Have replaced pump along with cleaning out the drain.
Use to say PAU before latch replaced.
Now won’t final spin on normal cycle.
I have a frigidaire affinity, it starts filling, fills about 5 seconds then stops for a few minutes.
Then does it all over again.
I pulled the code and it says E5E.
I looked at the fault code table and it says “communication error see test 11”
Mary,
If your Frigidaire Affinity Front Load Washing Machine is stuck on pause, try unplugging the washer for 10 minutes to attempt to reset it.
It that does not solve it, then you may have a faulty board or other issue in your washer (possibly mechanical).
What is the model number?
-RR
Frigidaire Affinity Front Load Washing Machine is stuck on pause.
I have a 4 year old Frigidaire Affinity Front Loader FAFs4073NW0, that was emitting error code E59, so I replaced the motor control board and wire harness, and ohmed out the motor to ensure working properly.
Now, when I attempt to wash a load from any of the selections, the machine fills with water, sits for 15 minutes or so with no tub motion, then emits code E59.
I then clear the error codes once, maybe twice, then the machine runs like normal for multiple loads. Once it goes cold for a day or so, i have to start the process all over.
I have a Frigidaire Front load Affinity washer FAFS4073NW0, 4 years old, and when I select a wash cycle it fills with water, sits for about 15 minutes with no tub motion, then emits error code E59.
I then have to clear the error codes at least once, maybe twice, then it runs like it is supposed to for multiple washes.
I have replaced the motor control board and wire harness, and ohmed out the motor.
I have a frigidaire affinity front load washing machine error code eb1 or e61 that open and close by itself